Assessments - 0, GPA: 4
(
)
)
|
Facilidade de uso
In typical use, alkaline batteries will last three years. 3.Test Range. Temporarily position chime where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 1. Open chime case: Press in catch on bottom of chime and lift the case open. Battery Chime Volume 2. Install the 3 alkaline "D" batteries. Make sure batteries are oriented properly. 4. Mount accessory chime. Chime can be mounted by using 3 holes in the back of case, or by using 2 screws with keyholes. Chime Back Case Keyhole Mounting Chime Back Holes for Wall Mounting 3-5/16" (8.4 cm) Close Chime Case Case Mounting Snap front of chime case on. Start with top edge of case aligned with the top of back plate. © 2007 598-1075-03 Code and Tune Settings Code Settings Note: Most installations will not require you to change any of the jumpers on your chime and push button. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Open the cases and locate jumpers on both the push button and chime (See illustration on page 3). 2. The push button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 3. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly.Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. Tune Settings Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available).This tune can be changed by following the instructions below. • Ding (one note tune) Push Button: Add a jumper to location 8. • Ding-Dong (two note tune) Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities.You may purchase any ACE® wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. -2- 598-1075-03 12 345 67812 345 678 Push Button Battery Replacement Install an alkaline type A23 12 Volt battery. The positive terminal should be positioned as shown. Inside Chime * Code Settings 1-7 Must Match Both Push Button and Chime Tune 12 345 678 Tune Setting Inside Push Setting (Not used on Button all models) Note: Some models might require the use of tweezers to remove and replace the jumpers. Troubleshooting Chime does not sound: • Make sure push button and chime codes are the same (See pages 2 and 3). • Check orientation of push button battery (See page 3). • Check charge of push button and chime batteries, replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. The range of the wireless chime can vary with location, temperature and battery condition. ACE® reserves the right to discontinue and to change specifications at any time without notice without incurring any obligation to incorporate new features in previously sold products. 598-1075-03 -3 Technical Service Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F).You may also write* to: HeathCo LLC P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. No Service Parts Available for this Product Regulatory Information This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this ...