Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
The paper cassette can hold up to 250 sheets of 75 g/m2 (20 lb.) paper. Use 60 to 90 g/m2 (16 to 24 lb.) paper. 1 4 5 Remove the paper cassette by ((a)) slightly lifting and ((b)) pulling it out of the unit. Remove the paper cassette cover. Press down on the silver plate until it is locked under the tab. Fan the stack of paper to avoid a paper jam. Insert the paper by aligning the paper edges with the paper level slot side on the paper cassette. • Most paper has instructions recommending which side to print on. Insert the paper with the print side facing down. •The height of the paper should not exceed the limit mark on the paper cassette or it may cause a paper jam. •When using legal size paper, see page 11. Paper level slot (continued) 9 Installation and Connection 6 Push down the opposite edges so they are secured under the clips Insert the paper stacker with the bent side facing up into the slots on the paper cassette cover —Check that the stacker ends are inserted properly 8 Close the paper cassette cover by inserting both tabs Dn the cover into the appropriate side slots Insert the paper cassette into the unit until it clicks into place Caution. ■ Every time the paper cassette is removed from the unit, the silver plate on the paper cassette must be pressed down and locked under the tab If you insert the paper cassette without lacking the silver plate, it may cause a paper jam Note: ■ Do not use different types or thicknesses of paper in the cassette at same time This may cause a paper jam ■ Avoid extremely smooth or shiny paper that is highly textured Also avoid paper that is coated, damaged or wrinkled paper with a cotton and/or fiber content that is over 20 % ■ Avoid used paper for double-sided printing ■ Do not use paper printed with this unit for double-sided printing with other copiers or printers, or a paper jam may occur ■ We recommend to use Hammermill® jet PRINT for clearer printing Using legal size paper 1 Press the button on the paper cassette to release the tray 2 Slide the tray so that “LGL^” on the tray aligns with “*<’ on the cassette and lock into place 3 Insert the paper by aligning the paper edges with the paper level slot side on the paper cassette 4 Extend the paper stacker until it clicks into place 5 Close the paper cassette cover by inserting both tabs on the cover into the appropriate side slots —The paper cassette cover does not cover the entire tray 6 Insert the paper cassette into the unit using both hands until it clicks into place 11 Installing the document stacker Insert the document stacker with the bent side facing up into the slots on the main cabinet Helpful hint: ■To extend the document stacker, pull it out of the unit until it clicks into place To save space, slide the document stacker into the unit until it clicks into place Installing the document feeder tray ^ Insert the three tray fins into the slots Dn the back Df the unit (®) Press the trc holders ((b)) 2 Press the tray down to place it on the two 12 i Connections Power socket Handset Handset cord Power cord Connect to LINE Dialing mode switch Set to TONE —If you cannot dial, set to PULSE DIALING MODE tone'^pulse Single telephone line (RJ11C) Telephone line cord (Line surge\ protector j (Power surge \ protector / Power outlet (120 V, 60 Hz) Note. • For additional equipment protection, we recommend the use of a surge protector The following types are available, TELESPIKE BLOK MODEL TSB (TRIPPE MFG CO ), SPIKE BLOK MODEL SK6-0 (TRIPPE MFG CO ), SUPER MAX (PANAMAX) or MP1 (ITW LINX) •When you operate this product, the power outlet should be near the product and easily accessible •The unit will not function during a power failure •To connect a RS232C cable (DB9 Female/DB25 Male), see the quick start guide Helpful hint • If assistance is needed, press (HELP) The unit will print a quick reference 13 Installation and Connection Setting the date, time, logo and facsimile telephone number — - - - Before using your unit, program the correct date and time, your logo and your facsimile telephone number This information will be printed on the top of each page transmitted from your unit Setting the date and time 1 Press [ MENU MENU) SYSTEM SET UP 2 3 Press («], then (□] (T) SET DATE & TIME Press [start/set; 4 Enter the correct month/day/year/hour/mmute by selecting each 2 digits Then press 0 for AM dt [#) for PM Example: Aug 10 1996, 3.00PM Press 00 HE 00 00 00i then press 0 for PM J Press (START/SET) g Press [MENU] Setting your logo_ CD CD GDI CD©®!a CDCD©!'a ©CD©!"О © culp Dial keypad a| [XI o| TO Q| in a| о о (11 . al □ a [START/SET] (STOP Note ■When you make a mistake while programming, press [STOP ] then make corrections ■The accuracy of the clock will be approximately ±60 seconds a month Usually the logo is a company, division or personal name in an abbreviated form Press (MENU) 1 2 3 SYSTEM SET UP (MENU)...