Assessments - 2, GPA: 3.5
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
If you try to charge any other type of battery (e.g., manganese batteries, alkaline dry cells, or one-time lithium batteries) than the batteries specified, those batteries may leak, overheat, or explode, causing the danger of burns or other injuries. • Be sure to charge both Nickel-Metal Hydride batteries at the same time. • When the batteries are charged, use them only in an environment where the temperature range is 0°C to 40°C (32°F to 104°F). Otherwise, there is a danger of leaks, explosions, excessive heat, fire, or electric shock. • Do not charge fully charged Nickel Metal Hydride batteries again. Otherwise, there is a danger of leaks, explosions, excessive heat, fire, or electric shock. • Do not peel off the external seals or damage the batteries. Never use batteries from which the seals have been partially or completely removed, or batteries that have been split in any way. • If you charge high-capacity batteries other than the supplied Nickel-Metal Hydride batteries, using the supplied BC-CS1 charger, they might not be charged to the extent the display indicators. Charging time Nickel-Metal Hydride battery Charging time NH-AA-DI x 2 (supplied) Approx. 13 hours This represents the time required to charge fully depleted Nickel-Metal Hydride batteries using the supplied BC-CS1 charger in an environment where the ambient temperature is 25°C (77°F). • Charging is complete in approximately 13 hours. The charge lamp may remain lit longer than 13 hours, but this is not a malfunction. • Do not disconnect the battery charger’s power cord (mains lead) or remove the batteries from the charger before the batteries are fully charged. If the charging process is interrupted before the batteries are fully charged, and then the same batteries are charged for the full 13 hours, this may cause the “memory effect” to occur, or may cause deterioration in the performance of the batteries. • If you use the ACC-CSNQ STAMINA “Super Quick charge” kit (not supplied), the batteries will charge faster. 15 Charging the Nickel-Metal hydride batteries (continued) Battery remaining indicator As the battery power decreases with use, the Battery remaining indicator displays the amount of power remaining using the following symbols. Battery remaining indicator Battery remaining guidelines (A full charge is 100%) Sufficient power remaining on Battery half full Battery low, recording/ playback will stop soon. "/1 Flashing Change the batteries for fully charged ones, or charge these batteries. If the LCD screen is off, press the DISPLAY/ LCD ON/OFF button to turn it on. Based on the conditions under which the camera is being used and the state of the charge, or on the environment, this information may not be correctly indicated. When the AC adaptor is being used, the Remaining battery information is not displayed. The POWER SAVE function When the POWER SAVE function is set to ON, you can shoot for a longer period of time. DSC-P71 Turn the Mode dial to SET UP, and set [POWER SAVE] in SETUP 2 to [ON]. The factory setting of the camera is set to [ON] (page 98). DSC-P51/P31 Set the POWER SAVE switch to ON. When the camera is shipped from the factory, this switch is set to ON. : O O o POWER SAVE OFFt .-ON rwtro When the POWER SAVE function is ON • The LCD screen will be darker than it is when POWER SAVE is set to OFF. You cannot change the settings for [LCD BACKLIGHT] at this time (page 98). To make the available shooting time even longer, it is recommended that you turn off the LCD screen and use the Finder to do your shooting (page 32). • In Flash mode, the ® (No flash) is displayed. If you want to shoot using the flash, press A ($) on the control button, and select (forced flash) or Auto (page 30). • When the power turns on, the Flash mode is normally set to ($) (No flash). • When the flash is charging ($ the Flash charge lamp blinks), the LCD screen turns off. • In shooting still images, the focus only focuses when the shutter is pushed down halfway. 16 the batteries , Open the Battery cover. Slide it in the direction of the arrow, and it opens out. , Insert the batteries. Match the +/- poles of the batteries to the +/ - marks inside the battery case. • Occasionally clean the poles of the batteries and the terminals of the Battery cover by wiping them with a dry cloth. If the poles of the batteries or the terminals become covered with a film of dirt or oil from the skin, the operating time of the camera can be greatly reduced. 3| , Close the Battery cover. Close the Battery cover while holding the batteries in. The cover is closed when it clicks. To remove the batteries Stand the camera on end, open the Battery cover upward, then remove the batteries. • Make sure you don’t drop the batteries when opening or closing the Battery cover. & t 3 (/) ST I 17 Inserting the batteries (continued) DSC-P51 1600x1200 640x480 Approx. 5600 Approx. 280 DSC-P31 1600x1200 640x480 Approx. 56...
Este manual também é adequado para os modelos :Câmaras - DSC-P51 (3.86 mb)
Câmaras - DSC-P71 (3.86 mb)