Assessments - 3, GPA: 3.7
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
If you use different types of print pack, printing may not be possible or malfunction may occur. • The side without the imprinting is the printing surface. Inferior print quality may result if the printing surface is contaminated with dust or fingerprints. Be careful to avoid touching the printing surface. • Do not bend the paper or tear it off at the perforations before printing. • Do not print on used sheets of print paper or attempt to rewind the ribbon inside the ink ribbon. Doing so could result in damages to the printer. PNotes on storing print packs (for quality prints) • When you are going to store a partially-used pack of the ink ribbon and print paper for an extended period of time, store it in its original bag or in a similar container. • Avoid placing the print pack in locations that are subject to high temperature, high humidity, excessive dust, or direct sunlight. • Use print pack within two years from the date of production. PNote on storing printouts • Do not affix cellophane tape or plastic erasers to printouts. Also avoid leaving printouts under plastic desk mats. Loading the ink ribbon 1 Pull and open the ink ribbon compartment cover. 2 Insert the ink ribbon in the arrow direction until it clicks into place. Eject lever Removing the ink ribbon When the ink ribbon runs out, the ERROR indicator will flash slowly. Open the ink ribbon compartment cover, push up the eject lever, and remove the used ink ribbon. PNotes • Use the ink ribbon contained in the same box with the print paper. • Do not touch the ink ribbon or place the ink ribbon in a dusty location. Fingerprints or dust on the ink ribbon may result in imperfect printing. Ink ribbon 3 Close the ink ribbon compartment cover. • Never put your hand into the ink ribbon compartment. The thermal head reaches high temperatures, especially after repeated printing. • Do not rewind the ink ribbon and use the rewound ink ribbon for printing. Otherwise, proper printing result will not be obtained, or even a malfunction may occur. • If the ink ribbon does not click into place, remove it and then re-insert it. If the ink ribbon is too slack to be loaded, wind the ink ribbon in the direction of the arrow to remove the slack. • Do not remove the ink ribbon while printing. Inserting the print paper 1 Open the paper tray. 2 Lift the paper tray lid up. 3 Set the print paper into the tray. You can set up to 20 sheets of print paper. Riffle the print paper thoroughly. Insert the print paper into the tray, with the protective sheet at the top. If there is no protective sheet: Riffle the print paper thoroughly. Then insert the print paper with its printing surface (the side with no imprint) facing up. Printing surface Paper feeding direction 4 Remove the protective sheet. 5 Close the paper tray lid. • Set the print paper toward the paper feeding direction with the back of paper with the SONY logo facing down. The back of print paper PNote Do not touch the printing surface. Fingerprints on the printing surface may result in imperfect printing. 6 Insert the paper tray into the printer. Insert the paper tray straight in until it reaches the end. PNotes • Do not remove the paper tray during printing. • To avoid paper jam or malfunctions of the printer, make sure the following before printing: – Do not write or type on the print paper. Use the oil ink pen to write on the paper after printing. You cannot type on the print paper using an ink-jet printer, etc. – Do not attach sticker or stamps on the print paper. – Do not fold or bend the print paper. – Total number of print paper does not exceed 20 sheets. – Do not print on the used print paper. Printing an image twice on the same paper will not make the printed image thicker. – Use the print paper for this printer only. – Do not use the print paper ejected without printed. PNote on storing the print paper • Avoid storing the paper with the printed faces touching each other or in contact with rubber or plastic products including vinyl chloride or plasticizer for an extended period of time; color changes or deterioration of the printed image may occur. Connecting 1 Insert the plug of the AC adaptor (supplied) to the DC IN 24V jack of the printer. 2 Insert one plug of the AC power cord to the supplied AC adaptor and insert the other plug of the AC power cord to the wall outlet (wall socket) close by. The 1 (on/standby) indicator lights in red. DC plug AC adaptor To a wall outlet (wall socket) (mains lead) AC power cord PNote The socket outlet shall be installed near the equipment and shall be easily accessible. 3 Connect the printer to a TV. Connect the printer to the high definition TV with the component video cable and the A/V connecting cable. Component video cable Component Red Audio White (monaural) A/V connecting cable • When both the Component video cable and the A/V connecting cable are connected, images will be output not via the A/V OUT jack, but via the COMPONENT OUT jack. • Set the “COMPONENT” setting of ...