Assessments - 5, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
To turn off the power Set the POWER switch to OFF sliding in the arrow direction. Attach the lens cap. After you remove the lens, store the camera with the body cap attached. Power Save (The camera nearly shuts down if it is not operated) If you do not operate the camera for about five seconds, the recording mode display on the LCD monitor disappears. Also, if you do not operate the camera for about three minutes, the camera turns to power saving mode and nearly shuts down (Power Save). To cancel the power save, operate the camera, for example, by pressing the shutter button halfway down. • You can change the time that must elapse to activate the function (the default settings are [5 sec]/[3 min]). t “User’s Guide/Troubleshooting” (page 120) Changing the language setting You can change the screen display to show messages in a specified language. To change the language setting, follow the procedure below. 1 Press MENU to display the menu. 2 Select [ ] t [1] with b/B on the multi-selector. 3 Select [ Language] with v/V on the multi-selector, then press the center of the multi- selector. 4 Select the desired language with v/V on the multi-selector, then press the center of the multi-selector. Shoot images easily (Auto adjustment mode) Shoot images easily (Auto adjustment mode) The main functions of the camera are adjusted automatically in auto adjustment mode. Using this mode, you can shoot easily, depending entirely on the camera. However, you can change any of the settings. 1Set the mode dial to AUTO. 4Shoot with the shutter button. • The image is not displayed on the LCD monitor before the recording is completed. Use the viewfinder for monitoring. • After shooting, the recorded image is displayed for two seconds on the LCD monitor. You can change the display time. t“User’s Guide/Troubleshooting” (page 111) • While the image is being recorded, the access lamp lights. Do not remove the memory card or turn off the power while this lamp is lit. Press the shutter button fully down to shoot. The shutter sounds. Press the shutter button halfway down to focus. Sensor used for focus adjustment (Illuminated in red briefly to indicate the point of focus.) Focus indicator (Indicates the status of the autofocus (page 15)) 2Hold the grip and look into the viewfinder. The subject at the intersection of (the 11 focus area sensors) comes into focus. 3When using a zoom lens, turn the zoom ring, then decide on your shot. Grip The number of images that can be recorded The number of images that can be recorded Once you insert a memory card into the camera and set the POWER switch to ON, the number of images that can be recorded (should you continue to shoot using the current settings) is displayed on the LCD monitor. To identify items on the LCD monitor t “User’s Guide/ Troubleshooting” (page 20) • The number of images that can be recorded on a memory card differs depending on the capacity of the memory card, the image size setting, and the image quality setting. t “User’s Guide/Troubleshooting” (page 24) • If “0” is flashing in yellow, the memory card is full. Replace the memory card with another one, or delete images in the current memory card (pages 8, 18). • Since the data amount of each image is different, the remaining number of recordable images may not change after shooting. Holding the camera Hold the camera steady to avoid blurring of images due to hand movement. Turning on the Super SteadyShot function is also recommended (page 14). • Grip the camera firmly with your right hand, keep your elbows at your side, and support the lens with the palm of your left hand. • Step out with one foot to stabilize your upper body. Leaning against a wall or putting your elbow on a table will also provide support. • When shooting in dark light without the flash, shooting in macro, or using a telephoto lens, camera shake that cannot be compensated for by the camera tends to occur. In such cases, turn off the Super SteadyShot function and use something to stabilize the camera, such as a tripod. Super SteadyShot functionSuper SteadyShot function 1 Make sure that the (Super SteadyShot) switch is set to ON to activate the function. 2 Press the shutter button halfway down, and then press it fully down. (Camera-shake warning) indicator Super SteadyShot (Super scale SteadyShot) switch Super SteadyShot scale This scale is displayed whenever the Super SteadyShot function is activated. A higher scale indicates more pronounced camera-shake (on a scale of five). When the Super SteadyShot function is deactivated, the scale will not be displayed. (Camera-shake warning) indicator This indicator flashes regardless of the status of the Super SteadyShot function. It indicates the likelihood of camera-shake calculated from the shutter speed and focal length. If the indicator flashes, reduce the camera-shake by setting the (Super SteadyShot) switch to ON or using the built-in flash or a tripod. • The Super SteadyShot function may not work optimally when ...
Este manual também é adequado para os modelos :Câmaras - DSLR-A700K (899.12 kb)
Câmaras - DSLR-A700P (899.12 kb)
Câmaras - DSLR-A700Z (899.12 kb)