Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
• Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center. Quick Start Basics 21 To format (initialize) a new memory card You need to format a new memory card before using it for the first time. 1. Turn on the camera and press [MENU]. 2. Select the “Set Up” tab, select “Format” and then press [6]. 3. Use [8] and [2] to select “Format” and then press [SET]. IMPORTANT! • Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card. • Be sure to use the camera to format a memory card. Formatting a memory card on a computer and then using it in the camera can slow down data processing by the camera. In the case of an SD or SDHC memory card, formatting on a computer can result in non-conformity with the SD format, causing problems with compatibility, operation, etc. • Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi Manager install files to your computer. Do this before formatting the card. Quick Start Basics 22 Turning the Camera On and Off Turning the Camera On and Off To turn power on To enter the REC mode, press [ON/OFF] (Power) or [r] (REC). To enter the PLAY mode, press [p] (PLAY). The back lamp will light (green) momentarily and the camera will turn on. If you are entering the REC mode, the lens will extend from the camera at this time. • Take care to ensure that nothing is restricting or coming into contact with the lens as it extends. Holding the lens with your hand so it cannot extend creates the risk of malfunction. •Pressing [p] (PLAY) while in the REC mode switches to the PLAY mode. The lens retracts about 10 seconds after switching modes. • The Sleep function or Auto Power Off (pages 158, 159) will turn off power automatically if you do not perform any operation for a preset amount of time. To turn off the camera [ON/OFF] (Power) Back lamp [p] [r] (PLAY) (REC) Press [ON/OFF] (Power). • You can configure the camera so power does not turn on when you press [r] (REC) or [p] (PLAY). You also can configure the camera to turn off when you press [r] (REC) or [p] (PLAY) (page 159). Quick Start Basics 23 To shoot a snapshot To shoot a snapshot 1. Press [r] (REC) to turn on the camera. Make sure R is on the display. If it isn’t, see page 55. Snapshot mode icon Monitor screen Shutter button [r] (REC) Remaining Snapshot Memory Capacity (page 188) 2. Point the camera at the subject. You can zoom the image, if you want. w Wide Angle z Telephoto Zoom controller Quick Start Basics 24 3. Half-press the shutter button to focus the image. When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green. Focus frame Half-press When you half-press the shutter button, the Press lightly camera automatically adjusts exposure and until the focuses on the subject it is currently pointed button stops. at. Mastering how much pressure is required Beep, beep (Image is in focus.) for a half-press and a full-press of the shutter button is an important technique for good- looking images. • The focus frame in the screen shots included in this manual is shown at .. Note that you can change the form of the focus frame, if you want (page 77). Back lamp 4. Continuing to keep the camera still, press the shutter button the rest of the way down. This records the snapshot. Full-press Shooting a Movie Press [0] (Movie) to start movie recording. Press [0] (Movie) again to stop movie recording. See page 50 for details. [0] (Movie) Snap (Image is recorded.) Quick Start Basics 25 . Using Quick Shutter Fully pressing the shutting button without waiting for Auto Focus to operate will record using Quick Shutter (page 79). • With Quick Shutter, the camera focuses faster than normal Auto Focus, which means you can capture quick moving action more easily. Note, however, that some images may be out of focus when Quick Shutter is used. • Whenever possible, take a little extra time to half-press the shutter button in order to ensure proper focus. . If the image does not focus... If the focus frame stays red and the back lamp is flashing green, it means that the image is not in focus (because the subject is too close, etc.) Re-point the camera at the subject and try to focus again. . If the subject is not in the center of the frame... “Focus lock” (page 69) is the name of a technique you can use when you want to shoot an image in which the subject to be focused on is not within the focus frame in the center of the screen. . To track the movement of a moving subject Half-press the shutter button to follow and focus automatically on a moving subject. See “E Tracking” (page 38) for more information. Quick Start Basics 26 Holding the Camera Correctly Hol...