Assessments - 2, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Quick Start Basics 22 If you make a mistake configuring display language, date, or time settings with the above procedure, refer to the following pages for information about how to correct the settings. – Display language: Page 108 – Date and time: Page 107 NOTE • Each country controls its local time offset and the use of summer time, and so they are subject to change. • Removing the battery from the camera too soon after configuring time and date settings for the first time can cause the settings to be reset to their factory defaults. Do not remove the battery for at least 24 hours after configuring settings. Preparing a Memory Card Though the camera has built-in memory that can be used to store images and movies, you probably will want to purchase a commercially available memory card for greater capacity. The camera does not come with a memory card. Images recorded while a memory card is loaded are saved to the memory card. When no memory card is loaded, images are saved to built-in memory. • For information about memory card capacities, see page 133. Supported Memory Cards – SD Memory Card (Up to 2GB) – SDHC Memory Card (2GB to 32GB) – SDXC Memory Card (32GB to 2TB) Use one of the above types of memory card. • The above are supported memory card types as of September 2011. • Noted memory card capacities are standard values. • Use only SD cards that are compliant with the SD Card Association specification. • This camera supports use of Eye-Fi cards. Quick Start Basics 23 1.Press [ON/OFF] (Power) to turn off the camera and then open the battery cover. Pressing the battery cover, slide it in the direction indicated by the arrow. To load a memory card 21To load a memory card 21 2. Load a memory card. Positioning the memory card so its front is facing downwards (towards the lens side of the camera), slide it into the card slot all the way in until you hear it click securely into place. Back Front Back 3. Close the battery cover. Pressing the battery cover against the camera, slide it closed. • For information about how to replace the memory card, see page 122. IMPORTANT! • Never insert anything besides a supported memory card (page 23) into the memory card slot. • Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center. 12 Quick Start Basics 24 To format (initialize) a new memory card You need to format a new memory card before using it for the first time. 1. Press [ON/OFF] (Power) to turn on the camera and then press [SET]. 2. Use [8] and [2] to select the second Control Panel option from the bottom (MENU) and then press [SET] (page 34). 3. Use [4] and [6] to select the “Set Up” tab. 4. Use [8] and [2] to select “Format” and then press [6]. 5. Use [8] and [2] to select “Format” and then press [SET]. IMPORTANT! • Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card. • Be sure to use the camera to format a memory card. Formatting a memory card on a computer and then using it in the camera can slow down data processing by the camera. In the case of an SD, SDHC, or SDXC memory card, formatting on a computer can result in non-conformity with the SD format, causing problems with compatibility, operation, etc. • Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi Manager install files to your computer. Do this before formatting the card. Quick Start Basics 25 Turning the Camera On and Off Turning the Camera On and Off To turn power on To turn on power and enter the REC mode [ON/OFF] (Power) Press [ON/OFF] (Power) or [r] (REC). • The back lamp will light green momentarily and the lens will extend out of the camera (page 28). To turn on power and enter the PLAY mode Back lamp Press [p] (PLAY). • The back lamp will light green momentarily and an image currently stored in camera memory will appear on the monitor screen (page 30). [p] (PLAY) [r] (REC) • Take care to ensure that nothing is restricting or coming into contact with the lens as it extends. Holding the lens with your hand so it cannot extend creates the risk of malfunction. •Pressing [p] (PLAY) while in the REC mode switches to the PLAY mode. The lens retracts about 10 seconds after switching modes. • The Sleep function or Auto Power Off (pages 109, 109) will turn off power automatically if you do not perform any operation for a preset amount of time. To turn off the camera Press [ON/OFF] (Power). • You can configure the camera so power does not turn on when you press [r] (REC) or [p] (PLAY). You also can configure the camera to turn off when you press [r] (REC) or [p] (PLAY) (page 110). Quick Start Basics 26 Holding the Camera Correctly Holding the Camera Correctly Your images will not come out cl...