Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
VGA (640x480) E Mail Image files are smaller, which is better when attaching images to e-mail. However, images are relatively coarser. • The initial factory default image size setting is “12M”. • Selecting “3:2” records images with an aspect ratio of 3:2, which matches the standard aspect ratio of print paper. • The letters “HDTV” stand for “High Definition Television”. An HDTV screen has an aspect ratio of 16:9, which makes them wider than the usual 4:3 aspect ratio of television screens of the past. Your camera can record images that are compatible with the aspect ratio an HDTV screen. • You should regard the print paper sizes suggested here as guidelines only (200 dpi print resolution). Snapshot Tutorial 32 . Specifying Movie Image Quality Movie image quality is a standard that determines the detail, smoothness, and clarity of a movie during playback. Shooting with the high-quality (HD) setting will result in better image quality, but it also shortens the amount of time you can shoot. 1. In the REC mode, press [SET]. 2. Use [8] and [2] to select the second Control Panel option from the top (Movie Image Quality). 3. Use [4] and [6] to select the setting you want and then press [SET]. Image Quality (Pixels) Approximate Data Rate Frame Rate HD 1280x720 24 Megabits/second 24 frames/second STD 640x480 10 Megabits/second 30 frames/second LP 320x240 2.7 Megabits/second 15 frames/second • The 16:9 aspect ratio is available only when “HD” is selected as the image quality. • Memory capacity (Movie recording time you can shoot) will be affected by the quality settings you configure (page 175). Snapshot Tutorial 33 1.In the REC mode, press [2] ( ) once. Using Flash (Flash)Using Flash (Flash) Flash 2. Use [4] and [6] to select the flash setting you want and then press [SET]. [2] ( ) Auto Flash > Flash fires automatically in accordance with exposure (amount of light and brightness) conditions. Flash Off ? Flash does not fire. Flash always fires. This setting can be used to brighten a Flash On < subject that normally comes out dark due to daylight or backlight (daylight synchro flash). Soft Flash _ Soft flash always fires, regardless of exposure conditions Red Eye . Flash fires automatically. This type of flash can be used to Reduction reduce the chance of redness in the subject’s eyes. 3. Press the shutter button to shoot. Back lamp Flashes orange while the flash is charging to indicate that image recording is disabled. • You will not be able to take another flash snapshot until the lamp stops flashing orange, which indicates < indicates the flash will fire. that charging is complete. • For information about Flash Range, see page 177. N Snapshot Tutorial 34 NOTE • Take care so your fingers and the strap do not block the flash. • The desired effect may not be obtained when the subject is too far away or too close. • Flash charging time (page 177) depends on operating conditions (battery condition, ambient temperature, etc.). • Shooting with flash turned off when lighting is dim results in a slow shutter speed, which can cause image blur due to camera movement. Under such conditions, secure the camera with a tripod, etc. • With red eye reduction, the flash is fired automatically in accordance with exposure. It does not fire in areas where lighting is bright. • The presence of outdoor sunlight, fluorescent lighting, or some other light source can cause abnormal image colors. • Select ? (Flash Off) for the flash setting when shooting in areas where flash photograph is prohibited. Red-eye Reduction Using the flash to shoot at night or in a dimly lit room can cause red spots inside the eyes of people who are in the image. This is caused when the light from the flash reflects off of the retina of the eye. When red-eye reduction is selected as the flash mode, the camera fires a pre-flash to cause the irises in the eyes of any people in the image to close, which reduces the chance of red eye. The camera also has an auto red-eye correction feature that corrects for red-eye in recorded images. Note the following important points when using red-eye reduction. • Red-eye reduction does not work unless the people in the image are looking directly at the camera (flash). • Red-eye reduction may not work very well if the subjects are located far away from the camera. Other Useful Flash Features • Changing the flash intensity (page 84) Snapshot Tutorial 35 Using the Self timer (Self-timer)Using the Self timer (Self-timer) With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time. 1. In the REC mode, press [SET]. 2. Use [8] and [2] to select the fourth Control Panel option from the top (Self-timer). 3. Use [4] and [6] to select the setting you want and then press [SET]. 10 sec Self-timer „ 10-second Self-timer 2 sec Self-timer ‚ 2-second Self-timer • When shooting under conditions that slow down the shutter speed, you can use this setting to prevent image b...