Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
• Tele Conversion Lens LU-8T: 1.5X • Focusing distance when installed QV-2300UX: Approximately 1m to . QV-2800UX: Approximately 2.5m to . Tele Conversion Lens (LU-8T) Conversion Lens Adaptor (LU-8A) • Wide Conversion Lens LU-8W: 0.7X • Focusing distance when installed QV-2300UX/QV-2800UX: Approximately 1cm to . Wide Conversion Lens (LU-8W) Conversion Lens Adaptor (LU-8A) QV-2300UX QV-2800UX QV-2300UX QV-2800UX E-22 GETTING ACQUAINTED IMPORTANT! • Be sure to use the Conversion Lens Adaptor whenever you install a conversion lens or filter. If you don’t, the lens will come into contact with the conversion lens or filter when it extends from the camera, resulting in malfunction. (QV-2300UX only) • Flash is disabled while a conversion lens is being used. • Setting the camera to wide-angle zoom while the Tele Conversion Lens causes shadows around the periphery of the image. This is because the frame of the attached filter or lens blocks some of the light coming into the lens. Because of this, you should always use telephoto zoom whenever you are using the Tele Conversion Lens. • The effects of hand shake are magnified while the Tele Conversion Lens is being used. Whenever you are using a conversion lens, install the cushion that comes with it and mount the camera on a tripod so it is secure. • Due to certain characteristics of the Wide Conversion Lens, you may notice some slight distortion in images recorded with it installed. • Make sure that (Macro Mode) is selected as the focus mode whenever you are using the Wide Conversion Lens. • Note that optical zoom is restricted a shown below in the Macro Mode . * QV-2300UX: 1X fixed (QV-2300UX) * QV-2800UX: 1X to 1.6X (QV-2800UX) • Use of the flash while a commercially available lens hood is installed may not produce desired results. Filters • The designs of some filters can cause shadows around the periphery of the image. • Auto focus and flash may not produce desired results while a filter is on the lens. • Filters do not produce exactly the same results as those obtained with a film-based camera. • Do not use multiple filters in combination. Lens Precautions • Fingerprints, dust, or any other soiling of the lens can interfere with proper image recording. Never touch the lens with your fingers. You can remove dust particles from the lens surface by using a lens blower to blow them off. Next, wipe the surface of the lens with a soft lens cloth. • The lens of this camera extends from its body when you turn on power and retracts when you turn off power. Take care not to subject the lens to undue force or impact, and never set the camera face down so the lens is in contact with a tabletop, etc. Be sure to remove the lens cap before turning on the camera. • Never remove the camera’s batteries or unplug its AC adaptor while the lens is extended. Doing so leaves the lens extended, and creates the risk of lens damage. E-23 GETTING ACQUAINTED Monitor Screen Indicators The following describes the different indicators and markings that appear on the camera’s monitor screen. REC mode Focus Mode indicator None Auto Focus Macro Infinity Manual Focus Flash Mode indicator None Auto Flash Off Flash On Red-eye reduction • Flash indicator indicates that the flash will fire (when auto flash is selected). Aperture value Shutter speed value • An out of range aperture or shutter speed causes the corresponding monitor screen value to turn yellow. Spot metering indicator Camera shake indicator Self-timer 10 SEC, 2 SEC Recording Mode indicator Zoom factor Battery capacity Auto Focus frame • Focusing complete: Green • Focusing failed: Red No memory card loaded warning EV value Memory capacity (Remaining number of storable images) Image size 1600 x 1200 pixels 800 x 600 pixels Quality FINE, NORMAL, ECONOMY Image information Movie Recording: recording time ........... seconds Panorama: number of images ........... P1 to P10 Date and time This information appears for one or two seconds, and then disappears. The recording mode, memory capacity, image size, quality, and battery capacity indicators do not appear on the REC mode monitor screen when the “Indicators” option is turned off (page E-113). E-24 GETTING ACQUAINTED n Screen when SHIFT INFO is pressed PLAY mode Exposure Mode indicator (program AE) (aperture priority AE) (shutter speed priority AE) (manual) SHIFT INFO MF SHIFT INFO button Metering Mode indicator (multi) (center) (spot) White balance (Auto) (Daylight) (Shade) (Tungsten) (Fluorescent) (Manual) Folder name Image protection indicator File number Image size Quality Battery capacity The above indicators do not appear on the PLAY mode monitor screen when the “Indicators” option is turned off (page E-113). E-25 GETTING ACQUAINTED n Screen when SHIFT INFO is pressed Operation Indicator Lamp The Operation lamp shows the operational status of the White balance Flash Mode indicator Recording Mode indicator camera as described below. Aperture Folder name value File number Operation lamp SHI...