Assessments - 0, GPA: 0
(
)
)
|
Fotos e especificações Olympus FL-600R |
Facilidade de uso
• Close supervision is necessary when any fl ash is used by or near children. Do not leave fl ash unattended while in use. • Care must be taken as burns can occur from touching hot parts. • Do not operate if the fl ash has been dropped or damaged - until it has been examined by qualifi ed service personnel. • Let fl ash cool completely before putting away. • To reduce the risk of electric shock, do not immerse this fl ash in water or other liquids. • To reduce the risk of electric shock, do not disassemble this fl ash, but take it to qualifi ed service personnel when service or repair work is required. Incorrect reassembly can cause electric shock when the fl ash is used subsequently. • The use of an accessory attachment not recommended by the manufacturer may cause a risk of fi re, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS Thank you for purchasing this Olympus product. To ensure your safety, please read this instruction manual before use, and keep it handy for future reference. ( gNames of Parts (Fig. p )p. 3) 1Wide panel 2Light-emitting area 3Remote sensor 4AF illuminator/LED window 5Auto light receptor 6Catch light plate 7Control panel 8AUTO CHECK lamp 9TEST button/CHARGE lamp 0OK button aBounce lock release button bBACK LIGHT button cON/OFF button dLatch eDial (a: flash compensation button; b: MODE button; c: LED light button; d: ZOOM button) Control Panel (Fig. p. 4) .. Details ( ((p p. 11, 18) )) 1Super FP flash 2Flash control mode 3Guide number (GN) 4Flash intensity control 5Zoom position (angle of illumination) 6FOUR THIRDS 7Zoom mode 8LED light 9ISO sensitivity 0RC mode group aAperture (F) bRC mode channel cTemperature warning dDistance units gContinuous Firing The flash may become hot when fired many times in succession, resulting in damage or malfunction. The flash should be fired no more than 10 times in succession at intervals of 2.5 seconds, after which it should be left unused for at least 10 minutes. pg y(ypSold Separately) )) Preparing a Battery ( Choose from the below batteries: • AA (R6) alkaline batteries (. 4) • AA (R6) NiMH batteries (. 4) x Note AA (R6) manganese batteries cannot be used. EN 7 g Loading Batteries 1 Open the battery compartment cover. 2 Insert the batteries with correct +/– polarity. 3 Close the battery compartment cover. g Attaching to the Camera Confirm that both the camera and electronic flash are off. Attaching or removing the electronic flash while either the flash or the camera is on may result in malfunction. 1 Slide the latch in the direction opposite to that indicated by the [LOCK..] icon (1). 1 3 2 Slide the flash into the hot shoe until it clicks securely into place (2). 2 3 Slide the latch to the [LOCK..] position (3). • To remove the flash, slide the latch in the direction opposite to the [LOCK..] arrow and slide it from the shoe. 8 EN g Turning on the Electronic Flash Attach an electronic flash to the camera, and then turn the camera on. Control panel AUTO CHECK lamp ON/OFF button CHARGE lamp 1 Press the ON/OFF button. • The control panel display will turn on. • To turn the flash off, press the ON/OFF button again. • Replace the batteries if the CHARGE lamp does not light after: 30 seconds (Alkaline batteries) 10 seconds (NiMH batteries) • If the CHARGE lamp and AUTO CHECK lamp blink simultaneously, batteries are running low. Replace the batteries. • The flash will enter sleep mode whenever the camera enters sleep mode. • If no operations are performed for approximately 60 minutes, the flash will turn off automatically. Press the ON/OFF button to turn it on. EN 9 gShooting Shooting AUTO CHECK lamp Firing angle Displayed according to the focal length of the lens. Flash control mode Light control range 1 Use camera controls to choose the fl ash mode. See the camera manual for details. 2 Choose a flash control mode. g“Flash control mode” (p. 11) 3Press the shutter button halfway. • The camera and flash will exchange shooting information and the flash range will be displayed in the control panel. • Flash range varies with camera settings (ISO sensitivity, aperture, and lens focal length). 4 Press the shutter button the rest of the way down to take the picture. The AUTO CHECK lamp blinks for about 5 s after shooting to indicate that the fl ash has fi red successfully. • When using a flash, flash light may be blocked by the lens body, lens hood, etc. • Use the wide panel to prevent overexposure at ranges of less than 1 m (3 ft.). 10 EN Flash Control Mode Choose a flash control mode according to your subject and shooting conditions. To select a mode, press the MODE (F) button and rotate the dial. Control operation The flash light intensity is controlled automatically according to the camera’s setup. The flash will be adjusted based on the brightness taken through the camera’s lens. Usually use this mode with a camera with communication capability. The flash will be adjusted based on the brightness captured by auto light receptor on the electr...
Este manual também é adequado para os modelos :Câmaras - FL‑600R (5.33 mb)