Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Discard used batteries according to the manufacturer's instructions. Replace the battery with a Sony CR123A lithium manganese dioxide battery. Use of another battery may present a risk of fire or explosion. WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. Slave Flash Features •The slave flash is for use with the Sony digital still camera. •You can also use the tripod while fitting the slave flash with the shoe adaptor. •The slave flash lets you take clear photos even when there is insufficient light from the built-in flash of the digital still camera. •The slave flash senses the reflected light from the built-in flash and fires of the digital still camera. (It does not fire with the pre-flash for red-eye prevention. It only fires in synchronization with the main flash.) •The distance at which photos can be taken with the slave flash is about one and half or two times that with only the built-in flash. AInserting the Battery The slave flash uses one Sony CR123A lithium manganese dioxide battery. 1 Slide open the battery cover in the direction of the arrow. 2 Insert the battery, making sure the polarity of the battery is correct. 3 Slide the battery cover closed in the direction of the arrow until it clicks into place. BFitting the Slave Flash 1 Fit the slave flash with the shoe adaptor provided. 2 Insert the screw of the shoe adaptor into the tripod hole of the digital still camera and lightly tighten it. 3 Adjust the length of the shoe adaptor and choose the position of the slave flash. 4 Firmly tighten the screw of the shoe adaptor. After Use •You can remove and attach the slave flash with the shoe adaptor still fitted to the digital still camera. Slide the slave flash in the direction of the arrow (5-2) while pressing the button at the bottom (5-1). •Remove the slave flash from the shoe adaptor when carrying. Using the Slave Flash For details of how to use the digital still camera, please refer to the digital still camera instruction manual. 1 Turn on the power switch of the digital still camera and set the power switch of the slave flash to the desired light control position. 2 Check that the slave flash’s READY lamp has stopped flashing and is glowing. The slave flash must be charged before taking a photo. Charging takes about 5 seconds (if the battery is new). When charging is complete, the orange power lamp stops flashing and glows. 3 Check that the built-in flash of the digital still camera is ready to fire. For details, please refer to the digital still camera instruction manual. 4 Point the digital still camera and focus before pressing the shutter button. When the built-in flash fires of the digital still camera, the slave flash senses the light and also fires. Note •The slave flash does not fire when there is no reflective object in the background. •Do not carry or rotate the slave flash with the digital still camera attached to the tripod. C •Switch off the slave flash after use. •The battery takes longer to charge as it gets older. •Even if the slave flash is charged when you turn it off, you must charge it again before it can fire. •Be careful not to block the light receptor with your finger during use. •The slave flash cannot be used outdoors or in sunlight because its sensitivity is reduced. •The slave flash may fire if facing a light source or if the light receptor is filled with a powerful light source (such as using a flash around you). •The slave flash can fire approximately 480 times with a new Sony CR123A lithium manganese dioxide battery and the light amount set to HIGH. This number varies according to the conditions of use. Recommended Distance The recommended distance varies with the guide number (GN) of the build-in flash of the digital still camera. For details, please refer to the digital still camera instruction manual. Example: When using a DSC-P100 built-in flash At f-stop 2.8, the recommended distance is 3.5 m. When using a DSC-P100 built-in flash and slave flash together (when this unit is set to HIGH) At f-stop 2.8, the recommended distance is 6.1 m. READY Lamp •Flashes orange... Charging is underway. •Glows orange... Charging is complete. The slave flash can now be used. •Flashes red... The battery is wearing out. Replace it with a new one. •Glows red for about 2 seconds then goes off... The slave flash will not fire even if it detects the built-in flash of the digital still camera, the object is within range, and the quantity of flash light is sufficient. •Glows green... The slave flash has fired. Maintenance Wipe the surface of the slave flash with a soft cloth. If it is very dirty, dampen the cloth slightly with a neutral cleanser and wipe again. Do not use thinners, benzene or alcohol, which damage the surface of the slave flash. Main Specifications Power Source 3 V DC lithium manganese dioxide battery Guide number Around 14 Max. No. of Flashes Approx. 480 Max. Dimensions 52.7 . 60.5 . 37.2 mm (2 1/ 8 . 2 1/2 . 1 1/2 inches...