Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
•Never look directly at the bulb while the video light is on. •Do not turn on the video light without the front window in place. •Avoid placing the video light near combustible or volatile solvents such as alcohol or benzine. •Do not let any solid object or liquid fall onto or into the video IR light. •Do not knock or jolt the video light while it is turned on as it may damage or shorten the life of the bulb. •Do not leave the video light on while it is resting on or against something; it may cause a fire or damage the video light. •The over-discharge safety circuit will turn the video light off automaticaly if the battery power goes below a certain level. Turn off the power and recharge the battery, or replace the battery to the fully-charged one. •While using the video IR light, the battery supplies power to both the camcorder and the video IR light. The recording time will be shorter compared with normal recording. •Do not pick up the camcorder by the head of the video IR light. •Remove the video IR light before putting the camera into a carrying case. •Do not place anything over the ventilation grill. •When the front window is hot, do not allow it to get wet. •Avoid placing or storing the video IR light in locations that are – Extremely hot such as in a car parked in the sun – In areas subject to direct sunlight or sources of high temperature, such a heating device – Vibrating After use • Be sure to set the POWER switch to OFF. • Store in pouch after making sure that the unit is cool enough to handle. On cleaning Clean the video light with a dry soft cloth. You can remove stubborn stains with a cloth lightly dampered with a mild detergent solution, then dry the unit with a soft cloth. Never use strong solvents, such as thinner or benzine, since these will damage the finish on the surface. Specifications IR light segment Power requirements 7.2 V DC Maximum power consumption 2.5 W Continuous lighting time Lighting duration Type of battery Used with camcorder pack (DCR-TRV10)* NP-FM50 78 (70) NP-FM70 161 (140) NP-FM90 245 (209) (Approx. minutes using fully-charged battery pack) Illumination distance Approx. 3-20 m Video light segment Power requirements 7.2 V DC Power consumption 3.7 W Halogen lamp 3.0 W Maximum luminous intensity Approx. 100 cd Lighting direction Horizontal Lighting angle 20 degrees Continuous lighting time Lighting duration Type of battery Used with camcorder pack (DCR-TRV10)* NP-FM50 60 (55) NP-FM70 135 (115) NP-FM90 205 (180) (Approx. minutes using fully-charged battery pack) Illumination range Approx. 1 m (3 1/5 ft) (100 lux), Approx. 2 m (6 1/2 ft) (25 lux), Approx. 3 m (9 4/5 ft) (12 lux) Colour temperature 3,000°K Average life of bulb Approx. 100 hours Dimensions Approx. 81 . 73 . 73 mm (3 3/16 . 2 7/8 . 2 7/8 inches) (w/h/d) Mass Approx. 95 g (3 1/3 oz) Accessories (supplied) Carrying case (1) Operating instructions (1) Accessory (not supplied) Halogen lamp XB-3D * When used in automatic mode with the LCD panel closed. Duration with the LCD panel open is shown in parentheses. Design and specifications are subject to change without notice. This mark indicates that this product is a genuine accessory for Sony video products. When purchasing Sony video products, Sony recommends that you purchase accessories with this “GENUINE VIDEO ACCESSORIES” mark. This mark indicates the Intelligent Accessory Shoe System for use with Sony video products. Video components and accessories equipped with this system are designed to make effective recording simple. AAttaching the video IR light to a camcorder To attach the video IR light 1 Insert the video IR light into the intelligent accessory shoe of your camcorder in the direction of the arrow and slit on its bottom until it reaches the end. 2 Turn the lock knob to LOCK and tighten it until you hear it click. To remove the video IR light Loosen the lock knob by turning it to RELEASE. Push down and pull out the video IR light in the opposite direction of the arrow to remove it. Notes •If you cannot insert the video IR light, turn the lock knob to RELEASE to cancel the lock. •Do not insert the video IR light backwards. Be sure to insert the video IR light in the derection of the arrow. • You can turn it in any direction you like to use. The video light can turn 270 degrees. BShooting in the dark (using the IR light) The IR light can be used on a camcorder with the NightShot function. For details of the NightShot operation, refer to the operating instructions supplied with the camcorder. 1 Set the POWER switch to ON of IR LIGHT. 2 Slide NIGHTSHOT on the camcorder to ON. The IR indicator lights up. Infrared lighting are emitted from the section . 3 View the picture in the viewfinder or on the LCD screen, and adjust the brightness by turning IR CONTROL. When the subject is far and too dark, turn IR CONTROL toward MAX. When the subject is close and too bright, turn IR CONTROL toward MIN. Tips •When you set N.S.LIGHT to ON in the menu system of the camcord...