Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Remote control (Pic. 2) 1 – ( ) button 2 –PHOTOS button 3 – WEATHER button 4 -CALENDAR button 5 -WEATHER + PHOTOS button 6, 11 – ^/Ў button 7 -MENU button 8, 14 – photo selection and menu/setting mode navigation buttons >/< 9 -ENTER button 10 - EXIT button 12 –ROTATE button 13 –ZOOM button 15 –SLIDESHOW button 16 –SETUP button Note: When the display is on, press any navigation button ^/Ў >/<, or ENTER, to switch on weather displaying mode during 1 minute. Remote sensor (Pic. 3) 1 – display 2 – battery compartment lid 3 – signal express-transfer button 4 – data transfer channel selection switch PRECAUTIONS 1. Before operating the units, read the instruction carefully. 2. Do not immerse the units into water. 3. Do not use abrasives or substances causing damages of the body and inner parts to clean the units. 4 6406_IM.indd 4 12.03.2010 10:19:41 ENGLISH ENGLISH 4. Do not apply hard efforts to the units, do not subjects the units to strikes (dust and moisture are also contraindicated), as it can lead to failures and correspondingly to the reduction of life time, damages of the batteries and to the deformation of the body details. 5. Do not dismantle the unit; it will lead to the ending of guarantee. There are no details, demanding attention of the user inside it. 6. Use only new and specified in the manual batteries. 7. Use the net adapter supplied. Connecting the net adapter to the base unit/placing batteries into the remote control and remote sensor: Connecting the net adapter to the base unit 1. Make sure that the adapter voltage corresponds to the voltage in the mains. 2. Using the external power supply jack, connect the net adapter to the base unit supplied (5.0V DC). Placing batteries in the remote sensor 1. Unscrew the screws on the battery compartment lid. 2. Insert 2 batteries of AAA type, following the polarity. 3. Close the battery compartment lid and tighten up the screws. Placing batteries in the remote control The remote control is supplied with the batteries CR 2025 inserted. To activate the remote control pull out the insulating insert. To replace the battery follow the instructions on the rear panel. Follow the polarity when replacing the batteries. Note: While long operation of the sensor in the conditions of extreme temperatures, the voltage of its batteries can be lowered, the operation radius of the remote sensor will be reduced. Synchronization of operation of the basic unit and the remote sensor As soon as the power adapter is connected to the base unit, it will start signal searching from the remote sensor during 4 minutes. Before it, you should open the battery compartment lid; select the data transfer channel, insert batteries in the remote sensor. After the batteries in the remote sensor are inserted, it will start transfer of data, which will appear on the display of the base unit. During signal searching by the base unit, press the TX button inside the battery compartment of the remote sensor for quicker data transfer. After the data from the remote sensor are received, they will appear on the display of the base unit. To find channels from the remote sensor you can do the following procedure. Enter the main menu, by pressing the 9 Exit button of the base unit or the 7 MENU button on the remote control. Use the >/< buttons to select the Settings mode. Press ENTER to confirm the mode. Use the Ў button to select the Receipt from external sensor item. Use the >/< buttons to select Search, press Enter to confirm the parameters. The base 5 6406_IM.indd 5 12.03.2010 10:19:41 ENGLISH ENGLISH unit will switch to the weather conditions displaying mode and will start signal search from the remote sensor, the symbol will be flashing in the upper right angle. Note: All setups from the base unit can be performed from the remote sensor. Press SETUP to enter Settings. Weather conditions display adjustment To receive more precise weather forecast you should enter your current weather conditions at the initial start-up of the unit. Enter the main menu, by pressing the 9 Exit button of the base unit or the 7 MENU button on the remote control. Use the >/< buttons to select the Settings mode. Use the ^/Ў buttons to select Weather forecast. Use the >/< buttons to select one of the following items Sunny, Partly cloudy, Cloudy, Rain or Lightning storm as initial weather conditions. Press Enter to confirm the parameters, press Exit to cancel the Settings mode. Weather forecast is built according to the dynamic of atmosphere pressure measuring. According to the collected data, the weather station can forecast weather for the next 1224 hours At radius of 30-50 km. Precision is about 70%. Sunny Partly cloudy Cloudy Rain Lightning storm Base unit operation modes The base unit has five operation modes Photo album Weather Photo and weather Calendar and clock Settings Use the >/< buttons to select the desired mode, press Enter to enter the desired mode. “Photo album” mode Store photos in the JPEG format on a USB ...