Assessments - 5, GPA: 3.2
(
)
)
|
Facilidade de uso
Handling Fuel warning Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. • DO NOT overfill fuel tank. Wipe up spills immediately. • Securely tighten fuel tank cap and close fuel container after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. • Move at least 3m (10 ft.) from refueling location before starting the engine. Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. After use • DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames. IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. Power edger oPerator's Manual 13 startIng cold engIne warningThe attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown. 1. Stop Switch Move stop switch (A) away from the STOP position. 2. Choke Move choke (B) to “Cold Start” ( ) Position. 3. Purge Bulb Pump purge bulb (C) until fuel will be visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5times. 4. Recoil Starter Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Firmly grasp right hand grip with left hand and fully depress throttle trigger to wide open position. Rapidly pull recoil starter handle/rope (D) until engine fires (or maximum five [5] pulls). 5. Choke After engine fires or five (5) pulls, move choke lever back to “Run” ( ) position. Hold throttle trigger fully depressed and pull starter handle/rope until engine starts and runs. Release throttle triggerand allow unit to warm up at idle for several minutes. NOTE If engine does not start with choke in “Run” position after 5 pulls, repeat instructions 2 - 5. a B C D 6. After engine warm up, gradually depress throttle trigger to increaseengine RPM to operating speed. 14 startIng warm engIne The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. warningThe attachment should not move at idle, otherwise serious personal injury may result. NOTE If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. 1. Stop Switch Move stop switch (A) away from the STOP position 2. Purge Bulb Pump purge bulb (C) until fuel will be visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. 3. Recoil Starter Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Rapidly pull recoil starter handle/rope (D) until engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. a C D stoppIng engIne 1. Throttle Release throttle and allow engine to return to idle before shutting off engine. 2. Stop Switch Move stop switch (A) to STOP position. a warningIf engine does not stop when stop switch is moved to STOP posi- tion, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using edger again. Power edger oPerator's Manual 15 operatIng technIques warningEngine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious in- jury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. 1. Before edging, water the area to soften the ground to make edgingeasier. Before edging, check the area and remove all obstacles and objectsthat could be thrown. 3. Plan to edge regularly to make it easier to keep a neat edge and toavoid having to make more...