Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. assembly wArningDo not perform maintenance or assembly procdures with engine running. Tools Required: 4 & 5 mm Hex Wrench Parts Required: ProSweep Gear Housing, Lower Drive Shaft Assembly, PAS or SRM-SB Power Head w/Shaft & Coupling. prosweep gear housIng assembly to lower drIve shaft assembly 1. Remove vinyl caps from attachment drive shaft. 2. Place brush gear housing assembly on a flat surface with gear housing shaft mount at 45° angle. 3. Remove gear housing locator screw (A) with 4 mm hex wrench. 4. Loosen gear housing mounting bolt (B) with 5 mm hex wrench. 5. Position lower drive shaft (end without serial number decal) into gear housing shaft mount. 6. Align hole in drive shaft housing with gear housing shaft hole (C) and seat lower drive shaft end into gear housing shaft mount. Install and tighten locator screw (A). 7. Tighten gear housing mounting bolt (B). A B C ProSweeP AttAchment 9 oPerAtor'S mAnuAl power head shaft/lower shaft assembly 1. Turn gear housing assembly over so that gear housing mounting bolt (E) faces upward. 2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-out position. CAUTION Thrown objects hazard. Install lower drive shaft so that gear housing mounting bolt (E) faces upwards. Otherwise debris will be thrown toward user. 3. Remove cardboard spacer from coupler, if necessary. 4. Carefully fit attachment drive shaft assembly into coupler (B) to decal assembly line (C), making sure that the inner lower drive shaft engages upper drive shaft mount. NOTE Short couplings fit flush to decal point (F). Long couplings are 4-3/4 in. long, and fit flush to line (C). 5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower drive shaft. Locator pin should snap flush in coupler. Full engagement will prevent further shaft rotation. 6. Secure lower shaft assembly to coupler by tightening clamping knob (D). A B D C F D B E A 10 operatIon wArningMoving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. NOTE Refer to your Pro Attachment Series or Split Boom Operator's Manuals for correct engine fueling, starting and stopping instructions. 1. Hold unit on your right side resting sweeper brushes on work surface. 2. Firmly grasp throttle grip with right hand and front handle with left hand. 3. Position ProSweep at an angle to the work surface well out in front of your body. wArning The sweeper brushes rotate towards the operator. Do not operate ProSweep at an angle with brushes close to your body which could result in loss of control and possible serious injury. 4. Accelerate to full throttle and allow brushes to push debris ahead. Sweep to an area where debris can be piled and collected. IMPORTANT Extended use of unit at low throttle settings could cause damage to clutch because of clutch slipping. 5. Debris may be swept out and away from corners by turning unit over to reverse brush direction. Grip unit securely using both hands. Operate throttle trigger with thumb of right hand. For extended use, reposition front handle to allow comfortable grip. Return handle to normal position for regular operation. wArning Turning ProSweep over to reverse sweeper drum rotation will cause debris to be swept toward operator. Reduce engine speed, and be alert for unstable footing caused by loose debris. 6. When sweeping wide areas, angle brushes to pile debris in rows; then collect material. 7. Use an angle of 15-30.. This helps direct debris and reduces operator fatigue. ProSweeP AttAchment 11 oPerAtor'S mAnuAl maIntenance wArning Always stop engine and disconnect spark plug before performing maintenance procedures, otherwise serious injury may result. A wArningMoving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Your ECHO attachment is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your attachment achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO dealer for repairs. skIll levels Level 1 = Easy to do. Most requi...