Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Never allow the rotating blade to operate directly against concrete walk or drive. MAINTENANCE AND STORAGE 1. Check the blade and engine mounting bolts at frequent intervals for proper tightness. 2. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition. 3. Never store the equipment with gasoline in the tank inside of a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. 3 This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see operating section of this manual for proper fuel and engine oil recommendations. FIGURE 2 i ASSEMBLY Right and left hand side is determined from behind the edger, in the operator's position. TOOLS REQUIRED (1) Adjustable wrench or 3/4" open end or box wrench (2) 7/16 1 open end or box wrench (1) 9/16 1 open end or box wrench CONTENTS OF HARDWARE PACK (See figure 1) A (3) Shoulder Bolts 3/8-16 Thread B (3) Belleville Washers 3/8" I.D. C (3) Lock Washers 3/8" I.D. D (3) Hex Nuts 3/8-16 Thread E (4) Carriage Bolts 1/4-20 x 1 1/4" Long F (4) Lock Washers 1/4" I.D. G (4) Hex Nuts 1/4-20 Thread H (2) Hex Bolts 1/4-20 x 1 1/4" Long I (2) Hex Lock Nuts 1/4-20 Thread J (1) Hex Bolt 5/16-18 x 1 3/4" Long K (1) Compression Spring 1 3/8" Long L (1) Flat Washer 5/16" I.D. M (1) Hex Lock Nut 5/16-18 Thread N (1) Grip 0 (1) Compression Spring 2" Long P (2) Cotter Pins LOOSE PARTS IN CARTON (See figure 2) R (1) Upper Handle S (1) Clutch Handle T (1) Lower Handle U (1) Clutch Rod V (1) Front Wheel 6" Dia. w (2) Rear Wheels 7" Dia. X (1) Clutch Plate Your new edger is shipped preassembled with the exception of the handle, rear wheels and front whee 1. Remove the edger and all parts from the carton. Make certain that all loose parts and literature are removed from carton before carton is discarded. 4 FIGURE 3. 2. Place lower handle into the slots in the rear frame. See figure 3. 3. Line up holes in handle with holes in frame. See figure 3. 4- Secure rear wheels (P) and lower handle (M) to frame with shoulder bolts (A), belleville washers (B) (cupped side of washer against the frame), lock washers (C) and hex nuts (D). See figure 3. FRONT WHEEL BELLEVILLE WASHER (B) LOCK WASHER (C) HEX NUT. (D) Assemble the front wheel (0) as shown in figure 4. Place shoulder bolt (A) through wheel, then belleville washer (B) (between wheel and frame, cupped side against the frame). Secure with lock washer (C) and hex nut (D). See figure 4. FIGURE 4. FIGURE 5. 6. Assemble the upper handle (R) to lower handle. Place the head of carriage bolts (E)to the outside of handle. Secure with lock washers (F) and and hex nuts (G). See figure 5. 5 I 7. Place clutch plate (X) on the left hand side of the upper handle as shown in figure 6. Secure in place with hex bolts (H) and hex lock nuts (I). GRIP (N) FIGURE 7 8. Place hex bolt (J) through bottom hole in clutch handle as shown in figure 7, then through hole in adjustment bracket. 9. Secure hex bolt with compression spring (K), fiat washer (L) and hex lock nut (M) on the inside of the adjustment bracket. 10. Place compression spring (0) over straight end of clutch rod (U). Place end of rod in spindle bracket assembly and secure with cotter pin (P). See figure 8. 11. Secure bent end of clutch rod to clutch handle with cotter pin (P). See figure 7. 12. Slip the handle grip (N) on the end of the clutch handle. It will slip on more easily if it is first soaked in warm, soapy water. 6 OPERATION 1. Fill the crankcase with oil using a high quality detergent oil classified "For Service MS". Use SAE 30 oil. Nothing should be added to the recommended oil. Place the engine level. Remove oil fill cap. FILL THEOILSUMPTO POINT OF OVERFLOW. Pour slowly. See figure 9. Fill the fuel tank with clean, fresh, lead-free, low-lead or regular grade leaded gasoline. DO NOT MIX OIL WITH GASOLINE. 3. Pull the choke control out to "choke" position if necessary. See figure 10. FIGURE 10 . Grasp the starter handle and pull out the cord rapidly. Return it slowly to the engine. 5. After engine starts, push choke control in gradually. A CAUTION Rotating cutting blade may throw objects causing personal injury. Always wear safety glasses or some other suitable eye protection at all times the engine is running. Keep area clear of bystanders and do not operate without guards in place. To stop the edger engine, push the grounding clip against the spark plug. See figure 11. Depth Control Adjustment - The clutch handle controls the clutching and declutching of the belt. To declutch, the handle is pulled back toward the operator. To move the clutch handle, first move it to the left so the handle is out of the notch. ADJUSTMENTS AC WARNING | Disconnect the spark plug wire and ground against the engine before performing any adjustments, re...
Este manual também é adequado para os modelos :Cortadores de grama - 246-596-000 (1.08 mb)