Assessments - , GPA:
(
)
)
Fabricante : Agri-Fab
Arquivo Tamanho: 1.16 mb
Arquivo Nome : 45-0298.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
3. Assemble four aerator knives on the outside of each single spool assembly. Rotate each knife to insert the locking tab into the spool plate, then align the square holes and secure with a 5/16" x 3/4" carriage bolt, 5/16" lock washer and 5/16" nylock nut. See figure 2. 4. Push split plastic bearings into each end of the spool tube. See figure 2. 5/16" x 3/4" CARRIAGE BOLT (F) 5/16" LOCKWASHER (N) 5/16" NYLOCK NUT (K) SPLITBEARING (W) SPLITBEARING (W) CAUTION: POINTS OF AERATOR KNIVES ARE SHARP! EXERCISE CAUTION AT ALL TIMES WHILE ASSEMBLING AND USING THE AERATOR. 1. Assemble eight aerator knives on the outside of each double spool assembly. Rotate each knife to insert the locking tab into the spool plate, then align the square holes and secure with a 5/16" x 3/4" carriage bolt, 5/16" lock washer and 5/16" nylock nut. See figure 1. 2. Push split plastic bearings into both ends of each double spool tube. See figure 1. FIGURE 2 5. Assemble a wheel bracket to the middle hole in the shaft so that the bracket hub faces the short end of the shaft. Fasten the bracket to the shaft using a 1/4" x 1-3/4" hex bolt and a 1/4" nylock nut. Tighten. See figure 3. 6. Pre-assemble a 3/8" x 1-1/4" hex bolt and 3/8" nylock nut to the smaller hole in the wheel bracket. Insert the bolt from the hub side of the bracket. Do not tighten till step 18. See figure 3. 5/16" x 3/4" CARRIAGE BOLT (F)5/16" LOCKWASHER (N) 5/16" NYLOCK NUT (K) SPLITBEARING (W) SPLITBEARING (W) 1/4" x 1-3/4" HEX BOLT (B) 1/4" NYLOCK NUT (L) 3/8" NYLOCK NUT (J) 3/8" x 1-1/4" HEX BOLT (C) SHORTEND FIGURE 1 FIGURE 3 ENGLISH 7. Assemble a single spool assembly, a 1" long spacer, a double spool assembly, a 1.33" long spacer and a 3/4" flat washer onto the short end of the shaft. See figure 4. 9. Assemble an end plate to the end of the tray using four 5/16" x 3/4" hex bolts and four 5/16" nylock nuts. Repeat for other end. Do not tighten till step 20. See figure 6. 5/16" x 3/4" HEX BOLT (E) 5/16" NYLOCK NUT (K) SINGLE SPOOLASSEMBLYDOUBLE SPOOLASSEMBLY1" LONGSPACER (S) 1.33" LONGSPACER (T)3/4" FLATWASHER (O) SHORT END FIGURE 6 FIGURE 4 8. Assemble a 2.38" long spacer, a 3/4" flat washer, the middle brace, a 3/4" flat washer, a 3.70" long spacer, a single spool assembly, a 1.33" long spacer, a double spool assembly, a 1.33" long spacer and a 3/4" flat washer onto the long end of the shaft. The bent lip of the middle brace must face the short end of the shaft. See figure 5. 10. Assemble the tongue to the tray, placing the slot's locking notch to the front. Use two 3/8" x 1" hex bolts, two 3/8" x 1-1/4" hex bolts, four 1/4" long spacers, and four 3/8" nylock nuts as shown in figure 7. Tighten. 3/8" x 1" HEX BOLT (D) 3/8" x 1-1/4" HEX BOLT (C) 1/4" LONGSPACERS (P) 3/8" NYLOCK NUT (J) LOCKINGNOTCH 2.38" LONGSPACER (Q) 1.33" LONGSPACER (T) 1.33" LONGSPACER (T) 3/4" FLATWASHER (O) MIDDLEBRACE3.70" LONGSPACER (R) 3/4" FLATWASHER (O) SINGLE SPOOLASSEMBLYDOUBLE SPOOLASSEMBLY FIGURE 7 FIGURE 5 ENGLISH 11. Assemble two 3/8" x 1-1/4" hex bolts, four 1/4" long spacers, and two 3/8" nylock nuts to the holes on the right side of the slot in the tray. Tighten. See figure 8. 12. Assemble the hitch bracket to the tongue using two 3/8" x 1" hex bolts, and two 3/8" nylock nuts. Tighten. See figure 8. 13. Assemble the hitch pin through the hitch bracket and the tongue. Secure the hitch pin with the hair cotter pin. See figure 8. 14. Turn the tray upside down. Place the ends of the shaft through the holes in the end plates (end plates must be loose). Make sure the middle wheel bracket is approximately aligned with the slot in the tray. If it is not, flip the shaft end for end. See figure 9. 15. Assemble a 3/4" flat washer and a wheel bracket onto each end of the shaft. Secure each bracket with a 1/4" x 1-3/4" hex bolt and 1/4" nylock nut. The wheel bracket on each end must point toward the front while the middle wheel bracket points toward the tray. Tighten. See figure 9. NOTE: Add extra 3/4" flat washers as shims if there is too much end play in the shaft after assembly is completed. 3/8" NYLOCK NUT (J) 3/8" x 1-1/4" HEX BOLT (C) 1/4" LONGSPACERS (P) 3/8" NYLOCK NUT (J) 3/8" x 1" HEX BOLT (D) HAIR COTTER PIN (G) HITCHPIN (H) 3/4" FLATWASHER (O) WHEELBRACKET1/4" x 1-3/4" HEX BOLT (B) 1/4" NYLOCK NUT (L) MIDDLEWHEELBRACKET FIGURE 9 UPSIDE DOWN VIEW FIGURE 8 16. Assemble a wheel to a wheel bracket as shown in figure 10. Use a 1/2" x 3-1/2" hex bolt, one 1/2" hex jam nut, and one 1/2" hex nylock jam nut. Adjust the nuts so that the wheel is held securely but will spin freely. Repeat on other side. See figure 10. 1/2" JAM NUT (M) 1/2" x 3-1/2" HEX BOLT (A) 1/2" NYLOCK JAM NUT (I) FIGURE 10 UPSIDE DOWN VIEW ENGLISH 3/8" x 1" HEX BOLT (D) 3/8" NYLOCK NUT (J) MIDDLEBRACE 17. Tip the aerator back and fasten the middle brace to the bottom of the tongue using two 3/8" x 1" hex bolts, and 3/8" nylock nuts. Do not tighten till step 20. See figure 11. CAUTION: The Lift Handle can drop to the rear u...