Assessments - , GPA:
(
)
)
Fabricante : Briggs & Stratton
Arquivo Tamanho: 1.14 mb
Arquivo Nome : 2c53b183-99c1-b544-a172-19b09c0331a2.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Retainer Springs INSTALL COVER 1. Attach cover assembly (A, Figure 4) to bag support bracket (B) using cover hinge pivots (C). Secure cover assembly to bag support bracket using hinge pins (D) and retainer springs (E) as shown. C D D E E B A 7 Bag Installation and Tube Assembly INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 5). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). A D Figure 5. Install Collector Bags A. Cover B. Collector Bags C. Grass Bag Hanger D. Bag Hanger Post B C B A 42” Mowers 42” Mowers CONNECTING UPPER AND MIDDLE TUBE 1. Slide the upper tube (A, Figure 6) over middle tube (B) and secure together using screw (C). In upper tube: - Third hole from end is for 42” mowers See Figure 6 for hole locations. C Figure 6. Middle and Upper Tube Assembly A. Upper Tube B. Middle Tube C. Screw, 1/4 x 3/4 8 Chute and Tube Installation Chute Installation 1. Install 5/16 x 3/4” carriage bolts (D, Figure 7) with 5/16 push nuts (E) to mower deck as shown. 2. Lift discharge deflector(B). 3. Place the holes of the chute (A) onto carriage bolts (D, installed in step 1), sliding the front edge of the chute under the hinge bracket. 4. Secure knob (C) onto carriage bolt (D) as shown. 5. Secure wing nut (F) onto carriage bolt (D) as shown. Figure 7. Install Chute A. Chute B. Discharge Deflector C. Knob D. Bolt, Carriage, 5/16 x 3/4 E. Nut, Push, 5/16 F. Nut, Wing A B C E E B D C A B E F D Figure 8. Connecting Tube Assembly to Lower Chute and Cover A. Upper Tube B. Cover C. Ridge, Upper Tube D. Ridge Cutout E. Lower Chute F. Strap, Rubber G. Pin H. Tube Assembly CONNECTING TUBE ASSEMBLY TO CHUTE AND COVER 1. Slide the upper tube (A, Figure 8) into cover (B) aligning ridge (C) with cutout (D) as shown. 2. Slide tube assembly(H) over lower chute (E). Secure tube assembly (H) to lower chute (E) using strap (F) and pin (G). G H THIS PAGE INTENTIONALLY BLANK 9 Normal Installation & Removal 10 Figure 9. Normal Installation & Removal A. Hitch Support Assembly B. Bag and Cover Support Assembly C. Shoulder Bolt D. Mount Pin E. Retainer Spring F. Hinge Pin G. Retainer Spring H. Cover Hinge Pivots I. Cover J. Bag K. Bag Hanger L. Ridge Cutout M. Upper Tube N. Ridge O. Tube Assembly P. Rubber Strap Q. Pin R. Chute S. Knob T. Carriage Bolt U. Wing Nut V. Discharge Deflector W. Carriage Bolt X. Support Mount F C P A T Q NORMAL INSTALLATION & REMOVAL Installation NOTE: See previous pages for more detailed installation and operation instructions if necessary. 1. Attach bag and cover support assembly (B, Figure 9) to hitch support assembly (A) by sliding the support mount (X) into place until full contact is made with the shoulder bolts (C). 2. Insert mount pin (D) through support mount (X) and upright of hitch assembly (A). 3. Secure mount pin (D) with retainer spring (E). 4. Attach cover assembly (I) to bag support assembly (B) using cover hinges pivots (H). Secure cover assembly (I) to bag support bracket (B) using hinge pins (F) and retainer springs (G). M N K E B S L 5. Raise the cover (I), and attach collector bags (J) using grass bag hanger (K) to hanger post (D, Figure 5). 6. Lift discharge deflector (V) up, and Place the holes of the chute (R) onto carriage bolts (T and W) sliding the front edge of the chute under the hinge bracket. 7. Secure knob (S) onto carriage bolt (T) as shown. 8. Secure wing nut (U) onto carriage bolt (W) as shown. 9. Slide upper tube (M) into cover (I) aligning ridge (N) with ridge cutout (L). 10. Slide tube assembly (O) over chute (R) securing tube assembly (O) to lower chute (R) using rubber strap (P) on tube assembly (O) to pin (Q) on chute (R). R C D I J G F G H U W V X O Normal Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger, the mower discharge deflector MUST be properly installed in the down position and retained by the spring latch. Removal 1. Unhook rubber strap (P, Figure 9) from pin (Q), then remove tube assembly (O) from chute (R) and from cover (I). 2. Lift cover (I) and remove bags (J) from bag and cover support assembly (B). Note: Support the cover during the next step. 3. Remove cover (I) by disconnecting retainer springs (G), then remove both hinge pins (F). 4. Remove bag and cover support assembly (B) from hitch assembly (A) by removing retainer spring (E), then removing mount pin (D). Note: To prevent loss of pins and retainer springs re-attach them to the cover, and bag and cover support assembly. 5. Remove wing nut (U) from carriage bolt (W). 6. Remove knob (S) from carriage bolt (T). 7. Lift up discharge deflector (V)and remove chute (R) from carriage bolt (T and W). IMPORTANT: See that discharge deflector (R) returns to the DOWN position. 11 MANUFACTURING, INC. Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 Briggs & Stratton Yard Power Products Group Copyright © 2007 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Simplicity Mfg. Inc. - S...