Assessments - 3, GPA: 4.3 ( )

Fabricante : Buhler Arquivo Tamanho: 9.35 mb Arquivo Nome : Língua de Ensino:

NOTE: The engine is equipped with a priming pump and does not require the fuel filter to be filled prior to the installation if the following filling procedure is followed. Install the new filter onto the filter head Tighten the filter until the gasket contacts the filter head surface Tighten the filter an additional 3/4 of a turn after the gasket contacts the filter head surface, or as specified by the filter manufacturer NOTE: If the filter is equipped with a water-in-fuel sensor, rotate the sensor to desired location, and reconnect the wiring harness. To prime the fuel filter, turn the ignition switch to the ON position and leave for two minutes The engine can then be started NOTE: The engine will, perhaps, run rough for several minutes until the air is out of the system. Replacement fuel filter element P/N: 86034027 F4-123 4 5 Operation 26 Check the Engine Supplemental Coolant The SCA protection additive level must also be checked whenever coolant is added or the cooling system filter is changed A test kit, complete with instructions, to check the concentration level is available from your Cummins dealer Follow the instructions in the kit to maintain proper SCA protection level 435/485/535 4-24 435/485/535 Operation 27 Change the Transmission Oil Filter (CAT TA22) The transmission filter (1) is located behind the transmission. The transmission filter is a spin-on type and is removed by turning it counterclockwise. NOTE: Dispose of used oil filters in accordance with federal, provincial, state, local laws and environmental regulations. To install the new filter, lubricate the O-ring on top of the new filter with clean transmission oil. Install the filter to the filter head, hand-tightening until the seal contacts the filter head. Tighten the filter an additional 1/2 to 3/4 turn. NOTE: Some oil, approximately 2 L (4 qt.), may be lost when the filter changed. Be sure to replenish the lost oil. Start the engine and check for leaks at the filter. Replacement transmission filter P/N: 86034346 NOTE: Do not operate the transmission with oil levels above or below the recommended levels. Either condition can result in overheating or loss of power and damage to the equipment. Operation 28 Optional - Change the Transmission Oil after first 250 hours of operation (CAT TA22) Check the oil level with the tractor parked on a level surface with the engine shut off. Operate the tractor a sufficient amount of time to warm up the transmission oil. Remove the drain plug (2) from the transmission housing and allow the oil to drain into a pan. Clean the drain plug with a none flammable cleaning solvent. Replace the drain plug and torque to 108 N.m (80 ft-lbs ± 5%). Refill the transmission with new oil through the fill tube (3) to the proper level as indicated by the sight gauge (4). NOTE: 3.8 L (1 US gal) of transmission oil will raise the level in the sight gauge 10 mm (0.4 inch). Visually inspect the transmission for leaks. Check for leaks under the transmission and around the drain plug. F4-99 3 4 Section 4 - Lubrication & Maintenance Every 250 Hours Donaldson® F4-100 1 F4-101 2 Section 4 - Lubrication & Maintenance Every 250 Hours Operation 29 Clean the Transmission Breather (CAT TA22 only) The transmission breather ( ) is located on the upper rearside ofthetransmission Unscrewandremovethe breather Clean the breather in clean, nonflammable solvent Re-install the breather F4-1021 Operation 30 Check the Air-Conditioner Drain Hoses A/C drain hoses are routed down inside the front cab door posts (two per side) and exit below the front frame Withdraw the hoses and inspect the dust valves (2) fitted to the end of each tube Ensure that they are sealing properly and that condensation from the A/C can drain away Clean when necessary If the dust valves are missing, replace Refit drain tubes between the fender and frame NOTE: Blocked drain tubes can lead to the A/C unit filling with condensation and leaking into the roof headliner causing damage to electrical components. F4-322 435/485/535 Section 4 - Lubrication & Maintenance Every 250 Hours Operation 31 by a qualified WARNING: NEVER SYSTEM. THE PRESSURE AT ALL TIMES, EVEN WHEN THE TRACTOR IS NOT RUNNING. DO NOT ATTEMPT TO SERVICE THE AIRCONDITIONING SYSTEM. IT IS POSSIBLE TO SUFFER SEVERE FROSTBITE OR INJURY FROM ESCAPING REFRIGERANT. SPECIAL EQUIPMENT AND INSTRUMENTS ARE REQUIRED TO SERVICE THE AIR-CONDITIONING SYSTEM WHICH USES R134A REFRIGERANT. SEE YOUR AUTHORIZED BUHLER VERSATILE DEALER F4-311 2 435/485/535 435/485/535 4-27 F4-69 F4-68 F4-32 Operation 32 Check the Weight Kit (Optional) Hardware Torques Check the hardware securing the front, upper rear and rear weight brackets and weights to the tractor. Front weight kit - Check the ten flanged nuts (1) securing the bracket to the tractor and torque to 633 N·m (467 ft-lbs). Check the weight mounting bolts (2) securing the weights to the weight bracket and torque to 480 N·m (354 ft-lbs). Check the tie rod nuts (3) and torque to...

Baixe o seu

Para fazer o download, introduza 2 dígitos :