Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
• Allow the engine to warm up before you begin edging. • Increase the engine speed before placing the blade in the cut. For best results, run the engine at full throttle while cutting. • Always work going away from people and solid objects such as walls, large stones, trees, automobiles, etc. • Be careful when edging near trees or valuable plants. The high speed metal blade may cut roots and cause damage to the plants. • If the blade stalls, immediately move the unit back slightly to allow the blade to restart. If the blade continues to stall, stop the engine, disconnect the spark plug, and inspect for block age or damage. _WARNING: Keep the blade area clean. Always release the throttle trig ger, move the powerhead ON/OFF switch to the OFF position, disconnect the spark plug (or disconnect power- head from power source), and make sure the blade has completely stopped turning before cleaning. SETTING THE EDGING DEPTH ,_ WARNING: Never attempt to adjust the cut depth when the engine is running. Always release the throttle trigger, wait until the blade stops turning, move the powerhead ON/OFF switch to the OFF position, and disconnect spark plug (or disconnect from power source) before making adjustments. 8 1. Loosen the depth adjustment knob. 2. Slide the wheel to the desired position. • Raising the wheel will increase the cutting depth. • Lowering the wheel will decrease the cutting depth. 3. Tighten the depth adjustment knob securely. MAINTENANCE SCHEDULE WARNING: Always stop unit and disconnect spark plug wire (or disconnect powerhead from power source) before performing maintenance. CARE AND MAINTENANCE TASK Check for loose fasteners and parts Check for damaged or worn parts Inspect and clean unit and decals Check or replace blade GENERALRECOMMENDATIONS The warranty on this attachment does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the edger attachment as instructed in this manual. CHECK FOR LOOSE FASTENERS AND PARTS • Blade nut • Fasteners CHECK FOR DAMAGED OR WORN PARTS Contact Sears Service Centre for replacement of damaged or worn parts. • Blade Shield -Discontinue use of edger if blade shield is damaged. INSPECT AND CLEAN UNIT AND DECALS • After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. • Wipe off unit with a clean dry cloth. WHEN TO PERFORM Before each use Before each use After each use Every 5 hours of operation BLADE MAINTENANCE _WARNING: The blade will continue to spin after the engine stops or after the throttle trigger has been released. To avoid senous injury, make sure the blade has stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the blade. _WARNING: Always replace a blade that is bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged blade. Use only specified replacement blade. Wear protective gloves when handling or performing maintenance on the blade to help avoid injury. • The blade is reversible. When the cutting edge on one side becomes worn, turn the blade over (see BLADE REPLACEMENT in the SER* VICE AND ADJUSTMENTS section). • Check blade for flatness periodically. Lay the blade on a flat surface to inspect for flatness. Throw away a blade that is not flat. 9 BLADE REPLACEMENT _WARNING: The blade wilt con tinue to spin after the engine stops or after the throttle trigger has been re leased. To avoid serious injury, make sure the blade has stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the blade. _ WARNING: Wear protec_ve gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. 1. To remove the blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. 2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Screwdriver _.WARNING: Perform the follow ing steps after each use: • Allow attachment and gearbox to cool before storing or transporting. • Store attachment with blade shield in place. Position attachment so that any sharp object cannot accidentally cause injury. • Store the attachment in a dry, well ventilated area out of the reach of children. SEASONAL STORAGE Prepare attachment for storage at end of season or if it will not be used for 30 days or more. If your edger attachment is to be stored for a period of time: 3. While holding the screwdriver in position, remove blade nut by turntng clockwise. 4. Remove both washers, and the blade from the blade shaft. Blade shield _ Blade t_Oi_+ hers Shaft Blade nut 5. Install new blade onto blade shaft. 6. Reinstall both washers and blade nut (counterclockwise). 7. Tighten blade nut firml...
Este manual também é adequado para os modelos :Cortadores de grama - 944.511572 (884.17 kb)