Assessments - 3, GPA: 4 ( )

Fabricante : Cub Cadet Arquivo Tamanho: 1.08 mb Arquivo Nome : Língua de Ensino:

If operator should leave tractor seat without turning off the PTO switch, the PTO will automatically disengage. Interlock safety switches are activated by the brake pedal, the PTO switch located on the control panel, and a switch located underneath the operator's seat. The interlock safety switches, activated by the brake pedal, PTO switch and seat switch serve to prevent starting the engine accidentally. The engine will not start unless: 1. the brake pedal is depressed, 2. the PTO is in the "OFF" position, 3. the operator is seated. H. LIFT HANDLE (1204 and 1210 Tractors Only) The lift handle is used to lift or lower equipment used with the tractor. The equipment can be set in multiple positions by depressing the button on the handle and releasing it when the desired position is reached. An additional feature has been provided to give increased float capability to the deck by depressing the button and rotating the pin into the slot as shown in Figure 8. 3 Figure 9. (1211 Tractor Only) 1. Hydraulic Lift Control Lever J. LIFT HEIGHT INDICATOR The lift height indicator will Indicate the height of deck attachment when installed. (See Figures 10 and 11.) Figure 8. (1204 and 1210 Tractors Only) 1. Lift Handle 2. Slot 3. Button 4. Pin HYDRAULIC LIFT CONTROL LEVER (1211 Tractor Only) NOTE The engine must be running in order to op-erate the hydraulic lift. The hydraulic lift control lever (see Figure 9 ) controls the raising and lowering of a mowing deck, if installed. The control lever is spring-loaded. To raise the equipment, move the lever back toward the tractor seat. To lower the equipment, move the lever forward. O LIFT HEIGHT INDICATOR 8 ô A. LIFT — ^V. HEIGHT ---INDICATOR Figure 11. (1211 Tractor Only) K. CAM LOCK KNOB (1204 and 1210 Tractors Only) The cam stop may be adjusted to allow the implement to return to a single height. (See Figure 12.) With implement in desired height position, release cam stop by turning locking knob counterclockwise. Turn cam stop until it contacts lift bracket on lift handle. Lock cam stop into this position by turning cam knob clockwise. Figure 12 1. Cam Stop 2. Locking Knob 3. Lift Handle 4. Lift Bracket NOTE Refer to the equipment manual for proper hitching instructions. CAM LOCK KNOB (1211 Tractor Only) The cam lock knob is used to adjust the cam stop, which will allow an attached implement to return to a single preset height. (See Figure 13.) With the implement at a desired height, release cam stop by turning locking knob counterclockwise. Turn cam stop until it contacts tang on rockshaft. Lock cam stop into this position by turning cam knob clockwise. â=>v Figure 13. (1211 Tractor Only) 1. Locking Knob 2. Cam Stop 3. Tang 4. Rockshaft Equipment is normally operated in a "Float" position (implement free to move upward). To operate equipment in a fixed "Locked" position where down pressure of the implement is required (blade work), remove frame cover and install bolt, 1/2 x 1-1/8 inch (not furnished with tractor), between the lift arm and lift bracket. (See Figure 14.) 9 1 Figure 14. (1211 Tractor Only) 1. Lift Bracket 2. Hole (Not Seen) For Bott 3. Lift Aim L. IGNITION/LIGHT SWITCH A WARNING Remove the key from the tractor when the tractor is not ¡n use to prevent accidental starting and battery discharge. The combination lights and ignition switch is a four-position switch. (See Figure 15.) IGNITION OFF ■ .ON/LIGHTS -ON START Figure 15 M. CHARGE INDICATOR This instrument indicates whether the alternator is charging or the battery is discharging. If it shows discharge continuously, investigate the cause to avoid completely discharging the battery and possible damage to the charging circuit. (See Figure 4,5 or 6.) N. HOUR METER The hour meter is located on the instrument panel. (See Figures 4, 5, 6 or 16.) It indicates the actual hours of engine operation, enabling the operator to deter- mine without guesswork when lubrication, change of oil or periodic inspections are necessary. It also provides a means of computing cost of specific jobs. The hour meter operates whenever the engine is running or the ignition key is in the "ON" position. O. THROTTLE CONTROL LEVER This lever controls the speed of the engine. When set in a given position, it will maintain a uniform engine speed. (See Figure 4, 5, or 6.) When using power take-off operated equipment, best performance is achieved with the throttle lever in the "FAST" position. This symbol shows slow position. * This symbol shows fast position. P. GEAR SHIFT LEVER (1204 Tractor Only) This lever is used to select various gear ratios provided in the transmission. There are four forward speeds and one reverse speed. Refer to "SPECIFICATIONS". (See Figure 4.) Q. CREEPER DRIVE AND GUARD (1204 Tractor Only) The 1204 tractor has a built-in creeper drive in first gear for extra slow speed at full power. There is also a creeper drive guard installed to preve...

Baixe o seu

Para fazer o download, introduza 2 dígitos :