Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Tighten securely. FRONT WHEEL TOE-IN/CAM BER The front wheel toe-in and camber are not adjustable on your tractor. If dam age has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/de part ment. TO REMOVE WHEEL FOR REPAIRS 1. Block up axle securely. 2. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose). 3. Repair tire and reassemble. NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. 4. Replace washers and snap retaining ring securely in axle groove. 5. Replace axle cover. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. Center Span Keeper Transaxle Pulley Stationary Idler Clutching Idler Engine Pulley Retaining Ring Washers Square Key (Rear Wheel Only) Axle Cover 24 TO START ENGINE WITH A WEAK BATTERY WARNING: Lead-acid batteries generate explo sive gases. Keep sparks, flame and smoking ma te rials away from batteries. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manu al). If “jumper ca bles” are used for emer gen cy starting, follow this pro ce dure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles. TO ATTACH JUMPER CABLES 1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis. 2. Connect one end of the BLACK ca ble to the NEGATIVE (-) terminal (C) of fully charged battery. 3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and bat tery. TO REMOVE CABLES, REVERSE ORDER 1. BLACK cable first from chassis and then from the fully charged battery. 2. RED cable last from both batteries. Weak or Dead Battery Fully Charged Battery REPLACING BATTERY WARNING: Do not short bat tery termi nals by al low ing a wrench or any other object to contact both terminals at the same time. Before con nect ing battery, remove metal bracelets, wrist watch bands, rings, etc. Positive terminal must be connected first to prevent spark ing from ac ci den tal grounding. 1. Lift seat pan to raised position. 2. Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from trac tor. 3. Install new battery with terminals in same position as old battery. 4. First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal 5. Connect BLACK grounding cable to negative (-) termi nal with remaining hex bolt and keps nut. Tighten se cure ly. Seat Pan Keps Nut Positive (Red) Hex Bolt Terminal Cover Cable Negative (Black) Cable 25 TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Pull bulb holder out of the hole in the backside of the grill. 3. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. 4. Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD AND GRILL ASSEMBLY 1. Raise hood. 2. Unsnap headlight wire connector. 3. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. 4. When replacing hood, be sure to reconnect the headlight wire con nec tor. Headlight Wire Connector Hood ENGINE TO AD JUST THROTTLE CON TROL CABLE The throttle control has been preset at the factory and ad just ment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, see engine manual TO AD JUST CARBURETOR The carburetor has been preset at the factory and ad just ment should not be necessary. However, minor ad just ment may be required to compensate for dif fer enc es in fuel, temperature, altitude or load. If the carburetor does need ad just ment, see engine manual. 26 STORAGE STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thor oughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. 1. Clean entire tractor (See “CLEAN ING” in the Maintenance section of this manual). 2. Inspect and replace belts, if nec es...