Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
3) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 3 03024 COVER ASSEMBLY SUPPORT ASSEMBLY ASSEMBLY 02543 HANG SUPPORT ASSEMBLY ON REAR DRAWBAR (See Fig. 2) Determine the correct support assembly for your tractor. The support assemblies are marked "A" and "B". Compare the drawbar illustrations below to the drawbar located at the rear of your tractor. Use the support assembly indicated for your tractor and discard the other support assembly. 2 FIG. 2 INSERT FLANGES FIRST INTO DRAWBAR SLOTS SUPPORT ASSEMBLY DRAWBAR SLOTS (Drawbar "A" shown) RETAINER SPRING PIN 02051 02051 INSTALL HIGH LIFT BAGGING BLADES (See Fig. 1) CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. NOTE: If you already have high lift bagging blades on your mower, store the supplied blades in a safe place for future use. Go on to step 2. 1. Raise mower to highest position to allow access to blades. 2. Remove blade bolts by turning counterclockwise. 3. Install bagging blades supplied with stamped "THIS SIDE UP" facing up towards mower, or, blades stamped with "GRASS SIDE" facing down towards grass. IMPORTANT: To ensure proper assembly, center hole in blade must align with star pattern on mandrel assembly. 4. Install and tighten blade bolts securely (45-55 Ft. Lbs. torque). 02544 HIGH LIFT BAGGING BLADE BLADE BOLT (SPECIAL) MANDREL ASSEMBLY FIG. 1 STAR PATTERN 1 02051 DRAWBAR PIN HOLE 1. Slide fl anges of support assembly into drawbar slots fi rst, then, pivot backwards inserting pin into drawbar pin hole. 2. Be sure support assembly is seated properly, then secure with retainer spring. DRAWBAR A Use Support Assembly Marked "A" DRAWBAR B Use Support Assembly Marked "B" 6 CONTAINER MOUNTING (See Fig. 5) 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center support tubes. 5 FIG. 5 CONTAINER ASSEMBLY (See Fig. 4) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 4 4 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowear anddetierioration. Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING Do notoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowear anddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 03022 COVER LATCH HANDLES CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING CENTER SUPPORT TUBES 7 LOWER CHUTE (See Fig. 6) 1. Raise and hold defl ector shield in upright position. 2. Place slot in lower chute over tab on mower and position lower chute over mower opening as shown. 3. Hook rear latch into fl ange hole on back of mower. 4. Hook front latch into hole in front gauge wheel bracket or under gauge wheel bracket on mower without a hole in bracket. 6 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. FIG. 6 UPPER CHUTE (See Figs. 7A & 7B) 1. Lower mower to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bagger indicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 7 FIG. 7B LEVEL MOWER • Be sure mower is properly leveled for best mower per for man ce. See your tractors owner's manual for ins truc tions 8 02783 REAR LATCH FRONT LATCH DEFLECTOR SHIELD TAB 03029 COVER HANDLE LOWER CHUTE FULL BAGGER UPPER INDICATOR CHUTE FIG. 7A 03023 BOSSES LATCH...
Este manual também é adequado para os modelos :Cortadores de grama - 960 72 00-10 (758.93 kb)