Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
1A, 1B & 1C) 1. Remove and discard the upper bolt on both sides of the drawbar. Using the same holes, install the shoulder bolts supplied and tighten securely. DRAWBAR SHOULDER BOLTS SUPPORT ASSEMBLY RETAINER SPRING PIN FIG. 1A REMOVE AND DISCARD UPPER BOLTS AND INSTALL SHOULDER BOLTS SUPPLIED FIG. 1C 2. Install adapter to both sides of support assembly as shown. BAGGER SUPPORT ASSEMBLY Determine which type drawbar you have on your tractor. Compare the drawbar illustrations below to the drawbar located at the rear of your tractor. Follow the support assembly instructions that apply to your type drawbar. DRAWBAR A DRAWBAR B 3. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 4. Be sure support assembly is seated properly and secure with retainer spring supplied. DRAWBAR B (See Fig. 1D) 1. Discard adapters provided - not required for drawbar type B. 2. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 3. Be sure support assembly is seated properly and secure with retainer spring supplied. 3064 SHOULDER BOLTS SUPPORT ASSEMBLY RETAINER SPRING PIN FIG. 1D FIG. 1B ADAPTER 6 CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunless containerisprope rlyissubjecttowear anddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 3 3 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 2 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 2 03024 COVER ASSEMBLY SUPPORT ASSEMBLY 7 02552 LOWER CHUTE (See Fig. 5) 1. Raise and hold defl ector shield in upright position. 2. Place slot in lower chute over tab on mower deck and position lower chute over deck opening as shown. 3. Hook rear latch into fl ange hole on back of mower deck. 4. Hook front latch into tab hole on front of mower deck. 5 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. REAR LATCH FRONT LATCH DEFLECTOR SHIELD FIG. 5 LEVEL MOWER DECK Be sure deck is properly leveled for best mower per for mance. See your tractors owner's manual for instructions. 7 TAB OPTIONAL FRONT GAUGE WHEEL WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen cracked ordamaged.Useonlyarecommendedreplacementcontainer. WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 03022 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center support tubes. 4 FIG. 4 COVER LATCH HANDLES CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING CENTER SUPPORT TUBES 03029 UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bagger indicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 6 COVER HANDLE LOWER CHUTE FULL BAGGER UPPER INDICATOR CHUTE FIG. 6B FIG. 6A 03023 BOSSES LATCH PIN ALIGNMENT SLOT RUBBER LATCH OPERATION TIPS FOR IMPROVED BAGGING OPE RATION: Follow the mower operation instructions in your tractor owner's manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will e...
Este manual também é adequado para os modelos :Cortadores de grama - 402345 (834.07 kb)