Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
• NOTE - There are two start/stop levers fitted. Either one can be used for starting the lawnmower. • IMPORTANT - Do not use the start/stop levers intermittently To Stop your Lawnmower 1. Release the pressure on the Start/Stop lever. P Q 1 How to Mow S 1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (S) 2. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection. Do Not Overload Your Mower Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Cutting Height Adjustment. The Motor is protected by a Thermal Cut-Out which is activated when the blade becomes jammed or if the motor is overloaded. When this occurs, stop and remove the plug from the power supply. The Thermal Cut-Out will only reset when the start/stop lever is released. Clear any obstruction and wait for a few minutes for the Thermal Cut-Out to reset before continuing to use the mower. Thermal Cut-Out Removing and Fitting the Blade Switch off, wait until the blade has stopped rotating and disconnect from the mains electricity supply BEFORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade 1. To remove the blade bolt, hold the blade firmly with a gloved hand and with a spanner, loosen the blade bolt by turning it anti-clockwise (T). 2. Remove the blade bolt, washer and blade.(T) 3. Inspect for damage and clean as necessary. 4. In the event of a blade becoming difficult to remove, insert a screwdriver (V1) into the hole (V2) to lock the drive, then use a spanner (13mm A/F) to loosen the blade bolt by turning the spanner anti-clockwise. Ensure the screwdriver is removed before atempting to turn on the machine. Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it with a new one. Fitting the Blade 1. Fit the blade to the shaft with the sharp edges of the blade pointing away from the shaft and you are able to read the text on the blade ‘This side to grass’ 2. Re-assemble blade bolt through the washer and the blade. 3. Hold the blade firmly with a gloved hand and tighten the blade bolt firmly with a spanner . Do not over tighten. T blade blade bolt washer V 1 2 Fault Finding Hints Fails to Operate 1. Is the correct Starting procedure being followed? See ‘To Start your Lawnmower’ 2. Is the Power Turned On? 3. Check the fuse in the plug, if blown replace. 4. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Poor Grass Collection 1. Disconnect from the mains electricity supply. 2. Clean the outside of the air intakes, the discharge chute and the underside of the deck. 3. Raise to a higher height of cut. See Cutting Height Adjustment. 4. If poor collection persists. Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Excessive Vibration 1. Disconnect from the mains electricity supply. 2. Check that the blade is fitted correctly? 3. If the blade is damaged or worn, replace it with a new one. 4. If vibration persists? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Lawnmower becomes heavy to push 1. Disconnect from the mains electricity supply. 2. In long grass or uneven ground, the height of cut should be raised to a higher position. See Cutting Height Adjustment. 3. Check that the wheels and rollers can rotate freely. 4. If problem persists? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Caring for your Lawnmower Cleaning • USE GLOVES • IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. (W1) 2. Using a soft brush - remove grass clippings from all air intakes (W2), the discharge chute (W3) and the grass box (W4). 3. Visimo Only - Using a soft brush, remove grass clippings from the vision window (W5). 4. Wipe over the surface of your lawnmower with a dry cloth (W6). • IMPORTANT:- Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. Storing your Cable (Visimo & Rollermo only) • Your electric cable can be wrapped around the cable wrap wing knobs to enable tidy and safe storage (X1). Storing your Lawnmower: • Loosen the wing knobs to enable the handles to be folded...
Este manual também é adequado para os modelos :Cortadores de grama - EASIMO EM032 (6.07 mb)