Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
See figure 3. FRONT WHEEL BELLEVILLE WASHER (B) HEX NUT, (D) 5. Assemble the front wheel (O) toward the inside of the unit as shown in figure 4. Place shoulder bolt (A) through wheel, then belleville washer (B) (between wheel and frame, cupped side against the frame). Secure with lock washer (C) and hex nut (D). See figure 4. FIGURE 4. 6. Assemble the upper handle (R) to lower handle. Place the head of carriage bolts (E)to the outside of handle. Secure with lock washers (F) and and hex nuts (G). See figure 5. 5 7. Place clutch plate (X) on the left hand side of the upper handle as shown in figure 6. Secure in place with hex bolts (H) and hex lock nuts (I). GRIP (N) FIGURE 7 8. Place hex bolt (J) through bottom hole in clutch handle as shown in figure 7, then through hole in adjustment bracket. 9. Secure hex bolt with compression spring (K), fiat washer (L) and hex lock nut (M) on the inside of the adjustment bracket. 10. Place compression spring (0) over straight end of clutch rod (U). Place end of rod in spindle bracket assembly and secure with cotter pin (P). See figure 8. 11. Secure bent end of clutch rod to clutch handle with cotter pin (P). See figure 7. 12. Slip the handle grip (N) on the end of the clutch handle. It will slip on more easily if it is firs soaked in warm, soapy water. 6 OPERATION 1. Fill the crankcase with oil using a high quality detergent oil classified "For Service MS". Use -»v SAE 30 oil. Nothing should be added to the recommended oil. Place the engine level. Remove oil fill cap. FILL THE OIL SUMP TO POINT OF OVERFLOW. Pour slowly. See figure 9. Fill the fuel tank with clean, fresh, lead-free, low-lead or regular grade leaded gasoline. DO NOT MIX OIL WITH GASOLINE. 3. Pull the choke control out to CHOKE position if necessary. See figure 10. FIGURE 10 Grasp the starter handle and pull out the cord rapidly. Return it slowly to the engine. 5. After engine starts, push choke control in gradually. CAUTION Rotating cutting blade may throw objects causing personal injury. Always wear safety glasses or some other suitable eye protection at all times the engine is running. Keep area clear of bystanders and do not operate without guards in place. To stop the edger engine, push the grounding clip against the spark plug. See figure 11. FIGURE 11 Depth Control Adjustment - The clutch handle controls the clutching and declutching of the belt. To declutch, the handle is pulled back toward the operator. To move the clutch handle, first move it to the left so the handle is out of the notch. NOTE The full range of depth positions for the edger may not be available until the belt has stretched with use. ADJUSTMENTS | WARNING \ Disconnect the spark plug wire and ground against the engine before performing any adjustments, repairs or maintenance. Front Wheel Adjustment The front wheel may be raised or lowered to give added cutting depth. Loosen the second bolt on the front wheel support bracket. Pivot the bracket up or down to desired height. Retighten bolt. See figure 12. 7 SECOND WHEEL BOLT SUPPORT BRACKET SPINDLE BOLT FIGURE 12 LUBRICATION Engine - Refer to separate engine manual for lubi ¡cation instructions. Wheels - The wheels require no lubrication. Spindle Bearing - The ball bearing in the spind e is lubricated and sealed at the factory and require: no lubrication. Lubricate all other moving parts v/ith engine oil. MAINTENANCE AfwARN Disconnect the spark plug wire and ground against the engine before performing any adjustments, repairs or maintenance. Blade Removal - Hold head of spindle bolt with a 3/4" or adjustable wrench and remove spindle lut. See figure 13. Engine Oil - Check oil level before starting en jine and after every 5 hours of operation. Add oi as necessary to keep level full to point of overflowing. Before removing plug, clean area around plug to prevent dirt from entering oil fill opening. Change oil after first 5 hours of operation. Thereafter, change every 25 hours. Change oil while en jine is warm. Oil may be drained thru oil drain plug. See figure 9. Crankcase capacity - 1 1/4 pints. FIGURE 13 Belt Removal - Remove the spark plug wire and ground. Remove the gasoline. 1. Tip the edger back so that it rests on the handle. 2. Remove the cotter pin securing the castle nut on the bottom of belt cover. See figure 14. FIGURE 14 3. Lift off the hex castle nut, belleville washer and belt cover. See figure 15. 4. Remove the old belt and replace with new belt. While the belt cover is removed, it is a good idea to apply a little grease to the pivot point on belt cover. See figure 15. 5. Reassemble the belt cover, making sure the new belt is over the engine pulley. 6. When tightening the castle nut, only tightt., enough to line up hole in bolt for cotter pin. DO NOT OVERTIGHTEN. Belt cover must pivot freely. See figure 15. 8 FIGURE 15 7. Set edger back on its wheels. Replace spark plug wire. OFF-SEASON STORAGE The follo...
Este manual também é adequado para os modelos :Cortadores de grama - 24596-8 (1.07 mb)