Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179 The model number and serial numbers will be found on a decal attached to the dethacther. You should record both the serial number and the date of purchase and keep in a safe place for future reference. MODEL NUMBER: 486.24219 SERIAL NUMBER: __________________ DATE OF PURCHASE:__________________ SAFETY Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • Read this owners manual carefully for operating and service instructions before attempting to assemble or operate the dethatcher. Be thoroughly familiar with the proper use of the dethatcher. • Read the vehicle owners manual and vehicle safety rules, and know how to operate the vehicle before using the dethatcher. • Read the lawnsweeper owners manual and safety rules, and know how to operate the lawnsweeper before using the dethatcher. • Never allow children to operate the tractor or dethatcher attachment, and do not allow adults to operate without proper instructions. • This dethatcher attachment has sharp tine points. Always handle with care and wear substantial foot wear when operating this dethatcher. • Do not allow anyone to ride or sit on the dethatcher, lawnsweeper or towing vehicle. • Keep the area of operation clear of all persons, particularly small children, and also pets. • Always begin with the transmission in first (low) gear and engine at low speed, and gradually increase speed as conditions permit. • Vehicle braking and stability may be affected with the attachment of this equipment. Be aware of changing conditions on slopes. Refer to safety rules in the vehicle owner's manual concerning safe operation on slopes. STAY OFF OF STEEP SLOPES. • Always operate up and down a slope, never across the face of a slope • This equipment should be operated at reduced speed on rough terrain, along creeks and ditches and on hillsides, to prevent tipping and loss of control. Do not drive too close to a creek or a ditch. • Follow the maintenance instructions as outlined in this owners manual. Look for this symbol to point out important safety precautions. It means — Attention!! Become alert!! Your safety is involved. HARDWARE PACKAGE CONTENTS NNOT SHOWN FULL SIZEPOQASHOWN FULL SIZEBCEFGDIJKLMH REF. QTY. DESCRIPTION A 1 Hex Bolt, 1/2" x 3-1/2" B 7 Hex Bolt, 5/16" x 1-1/2" C 2 Clevis Pin, 5/16" x 1-3/8" D 2 U-Bolt E 1 Transport Hook F 2 Washer, 5/16" G 2 Washer, 1/2" H 14 Washer, 3/8" I 2 Hair Cotter Pin, 3/32" REF. QTY. DESCRIPTION J 4 Hex Nut, 1/4" K 7 Hex Nut, 5/16" L 1 Jam Nut, Plain 1/2" M 1 Jam Nut, Nylock 1/2" N 2 Vinyl Cap O 2 Conduit Clamp P 2 Keeper Bracket Q 1 Nylon Tie ASSEMBLY CARTON CONTENTS 1. Spring Tines (7) 2. Frame Assembly 3. Gauge Wheel NOTE: On sweepers smaller than 42", use only five spring tines. • Assemble a vinyl cap onto each end of the frame tube. See figure 1. 5/16" NYLOCK NUT3/8" WASHER5/16" x 1-1/2" HEX BOLTVINYL CAPVINYL CAP 123 FIGURE 1 • Assemble a 1/2" washer, the wheel, another 1/2" washer and the 1/2" plain jam nut onto the 1/2" x 3-1/2" hex bolt. See figure 2. • Insert the bolt through the welded bracket and assemble the 1/2" nylock jam nut onto the bolt. Adjust the nuts so that there is no end play in the wheel and then tighten the nuts securely against the welded bracket. Make sure the wheel still turns freely. See figure 2. TOOLS REQUIRED FOR ASSEMBLY (1) 7/16" Wrench (2) 1/2" Wrenches (2) 3/4" or Adjustable Wrenches (1) Knife 1/2" WASHER1/2" x 3-1/2" HEX BOLT1/2" WASHER1/2" NYLOCKJAM NUTUse this hole for42" & 46" sweepersUse this hole forsmaller sweepers1/2" JAM NUT REMOVAL OF PARTS FROM CARTON • Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on pages 3 and 4. • Turn the frame assembly as shown in figure 1. • Assemble seven spring tines to the top of the frame tube. Use a 5/16" x 1-1/2" hex bolt, two 3/8" flat washers and a 5/16" nylock nut for each spring tine. Place one 3/8" flat washer on top of the frame tube and the second 3/8" flat washer on top of the spring tine. See figure 1. FIGURE 2 KEEPER BRACKETU-BOLT1/4" NYLOCK NUT • Assemble a conduit clamp onto each end of the sweeper height adjustment tube so that the straight part of the clamp is on top of the tube. See figure 3. • Remove the hitch brackets and the bolts, if present, from the ends of the sweeper's hitch tubes. Slide the transport hook onto the L.H. hitch tube as shown in figure 3. • Reassemble the hitch brackets and bolts to the hitch tubes. Refer to your sweeper owner's manual. If you have a 30" sweeper, skip these steps. • Make sure the sweeper height a...