Assessments - , GPA: ( )

Instruções de Operação Craftsman, Modelo 358.792403

Fabricante : Craftsman
Arquivo Tamanho: 889.33 kb
Arquivo Nome : cfce2584-08c8-4adf-8f90-136e6655e82d.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

NOTE: If you need assistance or find parts missing or damaged, call 1-800-235-5878. ASSEMBLY _.WARNING: If received as sembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. • A hex wrench (provided) is required for assembly. HANDLEBAR ASSEMBLY ,_ DANGER: RISK OF CUT. To avoid serious injury, the barrier portion of the handlebar must be installed as shown on the upper shaft of the powerhead to provide a barrier between operator and the spinning blade. At tach handlebar mounting bracket above arrow on safety warning decal on the upper shaft (powerhead end of unit). Ensure handlebar is positioned on mounting bracket at the end of the arrow on the handlebar decal. NOTE: Two mounting brackets are included with this attachment. Both brackets are provided to adapt this attachment for use with powerheads that have either a 1" (2.5 cm) diameter or a 7/8" (2.2 cm) diameter upper shaft. The correct bracket must be used to ensure that the handlebar is mounted securely to the upper shaft before use. Bracket Cover Mountinc Bracket ,_ I 1. Place the mounting bracket over the upper shaft above the arrow on the safety label. Be sure to use the correct mounting bracket for either the 1" (2.5 cm) or 7/8" (2.2 cm) di ameter upper shaft. 2. Position one of the bracket covers under the upper shaft and align the mounting bracket and the bracket cover screw holes. Insert two screws into the screw holes. 3. Secure the mounting bracket by tightening the screws with the hex wrench. 4. Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow. 5. Position the second bracket cover over the handlebar. Align the mounting bracket and the bracket cover screw holes. Again make sure the handlebar is at the end of the arrow. 6. Insert two screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench. KNOWEDGER YOURATTACHMENT READ THiS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR EDGER A'F]-AOHMENT,Compare the illustrations with your attachment to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Depth Adjustment Knob Gearbox BLADE The BLADE is designed to cut sod. OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: Cultivator ............ 358.79241 Blower .............. 358.79242 Pruner .............. 358.79245 Brushcutter* ......... 358.79244 *not designed for use with electric powerheads ,_ WARNING: Always disconnect powerhead spark plug (or disconnect powerhead from power source) before removing or installing attachments. REMOVING ATTACHMENT CAUTION: When removing or instal ling attachments, place the power- head and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Hanger j Shaft Blade Shield Wheel Edger Blade DEPTH ADJUSTMENT KNOB The DEPTH ADJUSTMENT KNOB is used to adjust the wheel for blade cut ting depth. Upper Shaft Coupler Attachment TIGHTEN Knob 2. Press and hold the locking/release button. Locking/Release Button Upper Shaft Attachment 3. While securely holding the upper shaft, pull the attachment straight out of the coupler. INSTALLING ATTACHMENT 1. Remove tile shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. 7 3.Pushtheattachmentintothecoupleruntilthelocking/ releasebutton snapsintotheprimary hole. 4.Beforeusingtheunit,tightenthe knobsecurelyclockwise. byturning coupleHole r Primary Guide Recess Upper Locking/ Attachment Shaft Release Button _WARNING: Make sure the lock ing/release button is locked in the primary hole and the knob is securely tightened before operating the unit. Using the wrong hole could lead to serious injury or damage to the unit. Secondary Hole Locking/Release Button in Primary Hole INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use, To install hanger on attachment: 1= Remove the shaft cap from the attachment (if present) and discard. 2= Press and hold the locking/release button. 3= Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION ALWAYS_Eye WE_:_. Protection Long Pad_i)i_i)nts_ Heavy Sho_ 1 _, When operating unit, stand as shown and check for the following: • Wear eye protection and heavy clothing. • Keep right arm slightly bent with right hand holding the trigger handle of powerhead. • Keep left arm extended with left hand holding the handlebar. • Keep unit below waist level. • Adjust edger wheel for proper cut depth. _;;_,WARNING: Never attempt to adjust the edger wheel when the unit is in operation. Always stop the powerhead, wait until the blade stops turn ing, and disconnect the spark p...