Assessments - , GPA:
(
)
)
Fabricante : Craftsman
Arquivo Tamanho: 1.26 mb
Arquivo Nome : b7a4dc17-b3d0-4782-92d8-ece2c02fa03c.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the tube. 1. Place the metal shield under the gearbox, and align the screw holes. Gearbox Shield 2, Insertandthreadthe4mounting screwsthroughtheholesofthe _earboxandthemetalshield. ightenevenlyandsecurelywith thehexwrenchprovided, INSTALLATION OF THE METAL BLADE _l_ WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. _I_WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Sears and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others. NOTE: The dust cup and retaining washer are located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the following assembly steps are in the parts bag. 1. Remove the retaining washer from the threaded shaft of the gearbox. Leave the dust cup on the shaft. 2. Install the blade and the retaining washer over the threaded shaft. 3. Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade. 4. Slide the blade and retaining washer onto the shaft of the gearbox. 5. Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade. 6. Install the blade nut by threading onto the shaft counterclockwise. Gearbox Shield \ Dust Cu Threaded Shaft Blade Retaining Washer ---_ Cupped__ Washer _",_-_ Nut NOTE: Make sure all parts are in place as illustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. 7. Align hole in dust cup with hole in side of gearbox by rotating the blade. 8. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening the blade nut. 9. Tighten blade nut firmly with a wrench while holding screwdriver in position. 10. Remove the screwdriver. 11. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use. KNOW YOUR BRUSHCUTTER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments, Save this manual for future reference, be _T_ Hanger Trimmer Shield _'-_ Blade Blade Shield BLADE The BLADE is designed for cutting grass, weeds, and brush up to 1/2 inch m diameter. TRIMMER HEAD The TRIMMER HEAD holds cutting line and is designed for cutting grass and light weeds. OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables ments to be installed. tachments are: Edger ............... Cultivator ............ Blower .............. optional attach- The optional at 358.792401 358.792410 358.792421 WARNING: Always disconnect powerhead spark plug before removing or installing attachments. REMOVING BRUSHCUTTER AT* TACHMENT (OR OTHER OPTIONAL ATTACHMENTS) CAUTION: When removing or installing attachments, place the powerhead and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. BLADE SHIELD The BLADE SHIELD provides protection from the spinning blade. TRIMMER SHIELD The TRIMMER SHIELD provides protection from the spinning trimmer head. Upper Tube Coupler Lower \ LOOSEN Attachment TIGHTEN Knob 2. Press and hold the locking/release button. UpperTube Lower Attachment 3. While securely holding the upper tube, pull the attachment straight out of the coupler. 10 INSTALLINGATTACH* OPTIONAL MENT 1. Remove the tube cap from the attachment (if present)and discard. 2. Position locking/release button of attachment into guide recess of upper tube coupler. Coupler Primary Hole Upper Locking/ Attachment Tube Release Button 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the tube cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION ALWAYS WEAR: Heavy, _ Protection Long Pants Boots _,. NOTE: This brushcutter attachment is not designed for use with electric pow erheads. When operating unit with brushcutte...