Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Move the PTO engagement lever forward slowly until the blades are turning. A WARNING: When the blades are engaged, keep feet and hands away from the discharge opening, the blades or any part of the deck. Be sure that the lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower or engine. For best results and to insure more even grass distribution, do not mow when lawn is excessively wet. A WARNING: Elefore leaving the operator’s position for any reason, disengage the blades, place the shift lever in neutral, engage the parking brake, shut engine off and remove the key. When stopping the unit to empty a grass bag, etc., follow the instructions above. This procedure will also eliminate “browning” the grass, which is caused by hot exhaust gases from a running engine. IMPORTANT: If you strike a foreign object, stop the engine. Remove wire from spark plug, thoroughly inspect the mower for any damage, and repair the damage before restarting and operating the mower. NOTE: If any problems are encountered, refer to the Trouble Shooting Guide on page 29. If unit stalls with speed control in high speed, or if unit will not operate with speed control lever in a low speed position, proceed as follows. 1. Place shift lever in Neutral. 2. Restart engine. 3. Place speed control indicator and shift lever in high speed position. 4. Slowly and with extreme caution release clutch-brake pedal fully. 5. Depress clutch-brake pedal. 6. Place speed control indicator lever in desired position. 7. Place shift lever in either forward or reverse, and follow normal operating procedures. OPTIONAL ACCESSORIES AVAILABLE Rear bagging grass catcher model 310 is available as optional equipment for the rear engine lawn tractors shown in this manual. A WARNING: The mower should not be operated without the entire grass catcher or chute deflector in place. NOTE: Under normal usage bag material is subject to wear, and should be checked periodically. Be sure any replacement bag complies with the mower manufacturer’s recommendations. For replacement bags, use only factory authorized replacement. A 30” mulching kit model 093 is available as optional equipment for model 1030 shown in this manual. A 38" mulching kit model 096 is available as optional equipment for model 1238 shown in this manual. 7 ADJUSTMENTS A WARNING: Do not at any time make any adjustment to rear engine lawn tractor without first stopping engine and disconnecting spark plug wire. THROTTLE CONTROL If adjustment is needed, refer to the separate engine manual packed with your unit. SPEED CONTROL LEVER ADJUSTMENT NOTE: When operating the unit initially or after replacing the belts, there will be little difference between the highest two speeds until after the belts have gone through a break-in period and have seated themselves into the pulleys. If the full range of speeds cannot be obtained on your unit, adjust the speed control lever as follows. 1. Place the transmission in neutral. (The unit will move freely when pushed forward and backward with the parking brake released.) 2. Disconnect the transmission shift rod by removing the cotter pin and flat washer. Remove ferrule from gear shift bracket. See figure 5. 3. Start the engine. 4. Place the speed control indicator and shift lever in the eighth (high speed) position. 5. Release the clutch-brake pedal completely, then slowly depress the pedal all the way (to park position). Hold the pedal in this position. 6. Turn the engine off. 7. After engine stops completely, release the clutch-brake pedal. 8. Disconnect the speed control rod by removing the cotterpin and flat washer. See figure 5. 9. Place the speed control indicator and shift lever in the third speed position. 10. Pull down on speed control rod so rod is at the bottom of slot in shift cam assembly. Adjust ferrule to fit into hole on clutch pedal bracket assembly. 11. Secure the speed control rod using the flat washer and cotter pin. 12. Reconnect the transmission shift rod using flat washer and cotter pin removed in step 1. NEUTRAL ADJUSTMENT 1. With engine off, disconnect transmission shift rod by removing the cotter pin and flat washer. Remove ferrule from gear shift bracket. See figure 5. 2. Place the transmission in neutral. (The unit will move freely when pushed forward and backward with the parking brake released). Place the shift lever in the neutral position. 3. Thread ferrule in or out as necessary to fit into hole of gear shift bracket. Secure with flat washer and cotter pin removed in step 1. Speed Control Indicator Nii Shift Lever Clutch Pedal Bracket Assembly FIGURE 5. 8 BRAKE ADJUSTMENT (See Figure 6) NOTE: Your brake may be equipped with a castle nut and cotter pin instead of the lock nut shown in figure 6. The brake is located by the left rear wheel inside the frame. During normal operation of this machine, the brake is subject to wear and will require periodic examination and...
Este manual também é adequado para os modelos :Cortadores de grama - 1238 (3.6 mb)