Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
5 (a) Each employer— (1) shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees; (2) shall comply with occupational safety and health standards promulgated under this Act. (b) Each employee shall comply with occupational safety and health standards and all rules, regulations and orders issued pursuant to this Act which are applicable to his own actions and conduct. OSHA Regulations Current OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the employer shall instruct every employee in the safe operation and servicing of all equipment with which the employee is, or will be involved.” These will include (but are not limited to) instructions to: Keep all guards in place when the machine is in operation; Permit no riders on equipment; Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing, adjusting, cleaning or unclogging the equipment, except where the machine must be running to be properly serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures which are necessary to safely service or maintain the equipment. Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the machine. EMPLOYEE TRACTOR OPERATING INSTRUCTIONS: 1. Securely fasten your seat belt if the tractor has a 5. Watch where you are going, especially at row ROPS. ends, on roads, and around trees. 2. Where possible, avoid operating the tractor near 6. Do not permit others to ride. ditches, embankments, and holes. 7. Operate the tractor smoothly - no jerky turns, 3. Reduce speed when turning, crossing slopes, and starts, or stops. on rough, slick, or muddy surfaces. 8. Hitch only to the drawbar and hitch points recom- 4. Stay off slopes too steep for safe operation. mended by tractor manufacturers. 9. When tractor is stopped, set brakes securely and use park lock if available. Child Labor Under 16 Years Old Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.) 5 SPECIFICATIONS MODEL SIZE TYPE HITCH HUBS SPOONS APPROX. WT. MPG-600 60” Lift 10 80 460 lbs. MPG-720 72” Lift 12 96 500 lbs. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Figure 1 MPG 600 PluggerTop Link Lift PointLower Lift PointsParking StrandMast Greasable Shaft SleeveSpoonsWeight RackSECTION I OPERATION WARNING DURING IMPLEMENT ADJUSTMENT KEEP BODY, HANDS AND FEET CLEAR OF SPOONS OR FRAME. ATTACHMENT The implement should be placed on level ground. Place the tractor rockshaft control in “position con- trol” (non-floating) for attaching and detaching the implement. “Draft control” or “position control” can be used while operating. Back the tractor until the ends of the lift arms can be attached to the lift points on the implement. Secure the lift arms to the lower lift points. (Figure 1) Attach the center link to the top of the mast and adjust so that the frame will be level in the operating position. Remove parking stands and store in the upside down position. DETACHING FROM TRACTOR Pin parking stands into position and lower the imple- ment to the ground with rockshaft control in position control. Remove top link from mast, disconnect hitch arms from bottom pins and pull tractor away from implement. 6 Figure 2MPG PluggerKnives should be assem- bled with two bladesbetween the two hubplates and two blades tothe outside of hub plates, on alternating sides. Weight BoxGrease Before Each Use OPERATION Level the implement from side to side and front to rear using adjustments on the tractor’s 3-point lift. WARNING DURING IMPLEMENT ADJUSTMENT KEEP BODY, HANDS AND FEET CLEAR OF SPOONS OR OTHER PARTS. Weight may be added to the plugger frame to aid in penetrating hard soil. Concrete blocks, water jugs or other types of weight may be used as long as noth- ing extends through the frame and interferes with the rotation of the spoons. Penetration should be approximately one to 1-1/2”. (Figure 2) By removing core plugs from the soil, lawns are bet- ter able to breath and hold moisture. Compacted soil and thatch are relieved, allowing air and fertilizer to reach roots. Optional slicing knives are available to replace spoons on the mounting plates. Four knives per hub are used to cut grass runners which causes new growth and thicker lawns. Install as shown. (Figure 3) Care should be exercised during use of the plugger to prevent hanging the spoons on immovable objects or otherwise use of the implement under conditions beyond its designed capacity. Figure 3 Optional Slicing Knives TRANSPORTATION CAUTION WHEN EQUIPMENT IS TRANSPORTED, USE N...
Este manual também é adequado para os modelos :Cortadores de grama - 720 (286.29 kb)