Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
ft 43 746-145 44 710-106 Hex Head Cap Screw 1/4—20 x 1-1/4 long * 45 710-606 Hex Head Cap Screw 1/4—20 x 1-1/4 long * 46 712-107 Hex Nut 1/4-20 Thread * 47 901-7969 Blade Adapter Kit 48 710-473 Truss Head Machine Screw #10 — 24 Thread * 49 712-526 Speednut * For faster service obtain standard nuts, bolts, and washers locally. If these cannot be obtained locally, order by part number and size as shown on the parts list. NOTE! This instruction manual covers various models, and all accessories shown do not necessarily apply to your model mower. MTD PRODUCTS INC extends its warranty only on the mower. If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines — Gasoline.” Find It Fast In The 'Yellow Pages' FORM NO. 770-2392C ASSEMBLY LUBRICATION Your new mower is shipped completely assembled with the exception of the handle and throttle control assembly. 1. Remove lawn mower and all parts from carton. Make certain that all loose parts and literature are removed from carton before carton is discarded. 2. Extend throttle control assembly, which is attached to engine, to rear of mower and place on floor. CAUTION: Do not bend or kink control wire. 3. Assemble upper handle to lower handle using four each screws and lock nuts provided in parts bag. 4. Assemble complete handle assembly to mower so that throttle control mounting hole in upper handle will be on right side. Holes at bottom of lower handle are to be fitted over studs located in front of each rear wheel mounting position. 5. Position throttle control assembly on right hand side of upper handle so that holes in control assembly and handle are in line. Secure in place with screw and lock nut found in parts bag. Secure throttle wire to lower right handle tube with clips in parts bag. OPERATION 1. Service engine with gas and oil. See engine manual packed with lawn mower for complete instructions for the care and maintenance of engine. READ DIRECTIONS CAREFULLY. 2. When ready to start engine, place throttle control lever, on handle, in “START” position and start engine in accordance with instructions in engine manual. After engine starts, move throttle control lever, on handle, to desired engine speed. The engine is stopped by placing control lever on handle in the “STOP” position. 3. Be sure that lawn is clear of stones, sticks, wire or other objects which could damage lawn mower or engine. For best results and to insure more even grass distribution, do not mow when lawn is excessively wet. ADJUSTMENTS CAUTION: Do not at any time make any adjustment to lawn mower without first stopping engine and disconnecting spark plug wire. CUTTING HEIGHT - Adjustment may be made by removing and moving wheel studs to desired position. Cutting heights will be raised as wheel studs are moved to a lower hole and lowered as wheel studs are moved to a higher hole in the deck. All wheel studs must be mounted in a relative position to the deck. THROTTLE - If adjustment becomes necessary, the throttle control wire assembly Can be reset as follows: 1. Loosen, but do not remove, screw securing throttle control wire assembly at engine. 2. Move throttle control lever on handle to “FAST” position. 3. Move lever, to which control wire is fastened at engine, to full open position and retighten screw to secure throttle control wire assembly. IMPORTANT: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on lawn mower. WHEELS - Wheel bearings are of lifetime Fortiflex. They require no lubrication. THROTTLE - Periodically lubricate throttle control lever and throttle wire assembly with a few drops of light oil (S.A.E. No. 10 or 20), for ease of operation. ENGINE - Follow engine manual for lubrication instructions. MAINTENANCE CUTTING BLADE - The blade may easily be removed for grinding or replacement as follows: 1. Remove bolt and lock washer holding blade and hub assembly to engine crankshaft. 2. Remove blade and hub assembly from engine crankshaft. 3. Remove two bolts, lock washers and nuts holding blade to blade hub. When sharpening blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the mower. Upon reassembly, make certain all parts are assembled properly and tightened securely. DECK - The underside of mower deck should be cleaned after each period of use as grass clippings, leaves, dirt and other matter will accumulate. This accumulation of grass clippings, etc., is undesirable as it will invite rust and corrosion and may cause an uneven discharge of grass clippings at the next cutting. The deck may be cleaned by tilting the mower forward or on its left sid...