Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Attach the grass catcher frame to grass catcher hitch bracket on rear of the mower by hooking grass catcher into hooks on grass catcher hitch bracket. See figure 9. 2. Lift the rear of grass catcher up. The roller on the grass catcher will push the chute door on the mower open. See figure 9. H^NOTE Figure 9 is shown with the chute door open for photo clarity only. 6 The grass catcher frame will snap into place, -secured by the lock lever. See figure 10. To remove the grass catcher, unhook the lock lever and slip the grass catcher off the unit. See figure 10. FIGURE 10. OPERATION DO NOT OPERATE THIS MOWER WITH THE CHUTE DOOR OPEN, UNLESS THE COMPLETE GRASSCATCHER IS PROPERLY MOUNTED ON THE MOWER. NOTE For shipping purposes your mower is set with the wheels in a low cutting height position. For best results, raise the cutting position until it is determined which height is best for your lawn. See adjustment section. BEFORE STARTING DANGER KEEP HANDS and FEET AUUAY FIGURE 11. Keep hands and feet away from the chute area on cutting deck. See figure 11. 1. Check to see that the handle is in the operating detent in the brackets on the deck, and the upstop projections restrict the handle from moving up and forward. If necessary, remove the left side from the mounting pin on the deck bracket. Push inward to decrease the spacing between the two sides of the handle until it is slightly less than the spacing of the deck brackets. Reinstall over the mounting pin and secure the hairpin cotter in the inner holes. 2. Fill sump with oil, using a high quality detergent oil classified “For Service SC, SD, SE or MS.” Use SAE 30 or SAE 10W-30 viscosity grade oil. Nothing should be added to the recommended oil. Place engine level. Remove oil fill plug. See figure 12. Fill to point of overflowing. Pour slowly. Capacity 11A pints. 7 I FIGURE 12. 3. Fill fuel tank, using clean, fresh leaded regular grade automotive gasoline. Fill tank completely. DO NOT MIX OIL WITH GASOLINE. TO START ENGINE 1. Move throttle control lever to “START” position. 2. Place foot on right side of deck and hold handle to prevent tipping the unit. Grasp starter and pull out rapidly. Return it slowly to the engine. Repeat if necessary. This mower is designed to be operated at full throttle to give you the best cut and do the most effective job of bagging the cut grass. TO STOP ENGINE 1. Move throttle control lever to “STOP” position. 2. Remove spark plug wire from spark plug and ground to prevent accidental starting while equipment is unattended. Be sure that lawn Is clear of stones, sticks, wire, or other objects which could damage lawn mower or engine. For best results and to insure more even grass distribution, do not mow when lawn is excessively wet. IMPORTANT If you strike a foreign object, stop the engine. Remove wire from spark plug, thoroughly inspect the mower for any damage, and repair the damage before restarting and operating the mower. warnTng Unless the entire grass catcher is correctly positioned on the mower, do not open the discharge chute door when the engine is running. USING YOUR ROTARY MOWER For the best results, do not cut wet grass because it tends to stick to the underside of the mower, preventing proper bagging of grass clippings. If wet grass must be cut, reduce walking speed. New grass, thick grass or wet grass may require a narrower cut. Blade speed should be adjusted to the condition of the lawn. For best results, cut off one-third or less of the total length of the grass. Lawn should be cut in the fall as long as there is growth. ADJUSTMENTS CAUTION Do not at any time make any adjustment to lawn mower without first stopping engine and disconnecting spark plug wire. CUTTING HEIGHT An adjusting plate and thumb lever at each wheel position provides cutting height adjustment. Each adjusting plate has five holes. Height of cut will be changed when the thumb lever is moved from one hole to another. Simply depress the lever towards wheel and move wheel and lever assembly to desired position. See figure 13. 5 V m m FIGURE 13. Cutting height will be raised as front and rear levers are lowered. Cutting height will be lowered as front and rear levers are raised. All wheels must be placed in the same relative position. For rough or uneven lawns, move the wheels to a position which will give a higher cutting height. 8 HANDLE POSITION The upper handle can be adjusted to a high or low position. The adjustment is made by removing the two knobs or hex nuts and lock washers, removing the two curved carriage bolts and reassembling in the other position. See figure 14. CARBURETOR ADJUSTMENTS ? : •T , Low Position *r High Position FIGURE 14. THROTTLE If adjustment becomes necessary, the throttle control wire assembly can be reset as follows: 1. Loosen, but do not remove, screw securing throttle control wire assembly at engine. See figuré 15. 2. Move throttle control lever on handle...