Assessments - 3, GPA: 3.3 ( )

Fabricante : Bolens Arquivo Tamanho: 2.22 mb Arquivo Nome : 29f05d55-698b-435a-947f-14f4b3881f67.pdf Língua de Ensino:

To adjust carburetor, refer to the separate engine manual packed with your mower. NOTE: A dirty air cleaner will cause an engine to run rough. Be certain air cleaner is clean and attached to the carburetor before adjusting carburetor. Refer to the separate engine manual. NOTE: When tipping the unit, empty the fuel tank and keep engine spark plug side up. TROUBLE SHOOTING Refer to page 11 of this manual for trouble shooting information. CUTTING BLADE When removing the cutting blade for sharpening or replacement, protect hands by using heavy gloves or a rag to grasp the cutting blade. Remove the bolt and bell washer which hold the blade and adapter to the engine crankshaft. Remove the blade and adapter from the crankshaft. If the blade or blade adapter needs replacing, remove the two small bolts, lock washers and nuts which hold the blade to the adapter. 9 I A WARNING: Periodically inspect this blade adapter for cracks, especially if you strike a foreign object. Replace when necessary. When sharpening the blade, follow the origins I angle of grind as a guide. It is extremely important th at each cutting edge receives an equal amount of grirding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the mower an i could break, causing personal injury. It is recommended that the blade always be re moved from the adapter for the best test of balance. The blade can be tested by balancing it on a rourd shaft screwdriver. Remove metal from the heavy side until it balances evenly. Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft c nd the inner surface of the blade adapter with li»jht oil. Lubricating the bolt holes, bolts and inner surface of the nuts with light oil is also recommended. 4 oz. plastic bottle of light oil lubricant is available Order part number 737-0170. Engine oil may also be jsed. When replacing the blade, be sure to install th 3 blade with the side of the blade marked “Bottom” lor with part number) facing the ground when the mov\ er is in the operating position. Blade Mounting Torque Center Bolt: 450 in. lbs. min., 600 in. lbs. max. Blade Adapter Bolts: 200 in. lbs. min., 350 in. lbs. max. To insure safe operation of your unit, all ni ts and bolts must be checked periodically for correct tightness. DECK The underside of the mower deck should be cleaned after each use to prevent a buildup of grass clippings, leaves, dirt or other matter. If this debris is all< >wed to accumulate, it will invite rust and corrosion, a id may prevent proper mulching. The deck may be cleaned by tilting the mower and scraping clean with a suitable tool (make cer ain the spark plug wire is disconnected). ENGINE Refer to the separate engine manual for engine maintenance instructions. Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully. Service air cleaner every 25 hours under normal conditions. Clean every few hours under extreme y dusty conditions. Poor engine performance and f ooding usually indicates that the air cleaner should be serviced. To service the air cleaner, refer to the sBparate engine manual packed with your unit. The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each mowing season; check engine manual for correct plug type and gap specifications. Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all grass, dirt and combustible debris from muffler area. OFF-SEASON STORAGE The following steps should be taken to prepare lawn mower for storage. 1. Clean and lubricate mower thoroughly as described in the lubrication instructions. 2. Refer to engine manual for correct engine storage instructions. 3. Coat mower’s cutting blade with chassis grease to prevent rusting. 4. Store mower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer. NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust-proof the equipment. Using a light oil or silicone, coat the equipment, especially cables and all moving parts. HANDLE STORAGE The handle may be placed in an upright position for storage. Move hairpin clips to outer hole on weld pins. See figure 1. Press inward on the bottom of the lower handle and push forward. The handle will lock in this position. To place the handle in the operating position, remove the starter rope from the rope guide. Grasp the lower handle at the bottom, press inward slightly and tip the handle backward. Place the hairpin clips in the inner holes. With the spark plug wire disconnected and grounded, depress the blade control handle and pull the starter rope out...

Baixe o seu

Para fazer o download, introduza 2 dígitos :