Assessments - 6, GPA: 4.3
(
)
)
|
Facilidade de uso
Do Not allow discharge to be pointed in the direction of persons. 20. No one should operate this unit while intoxicated or while taking medication that impairs the senses reactions. 3 H c FIGURE 1 Q-*-(§: FIGURE 2 ASSEMBLY INSTRUCTIONS CONTENTS OF HARDWARE PACK (See figure 1) A (1) Clutch Grip Assembly* B (1) Hair Pin Cotter* C (1) Clevis Pin* D (1) Extension Spring* E (1) Lock Nut 1/4-20 Thread* F (3) Hand Knobs G (3) Belleville Washers H (1) Heavy Flat Washer I (4) Hex Bolts 1/4-20 x 1.75" Long J (4) Hex Lock Nuts 1/4-20 Thread K (2) Stud Pins L (2) Push-on Speed Nuts M (1) Hex Jam Nut 1/4-20 Thread* LOOSE PARTS IN CARTON (See figure 2) N (1) Nozzle 0 (1) Upper Handle P (1) Air Duct Assembly Q (1) Clutch Rod* R (1) Directional Discharge Assembly S (1) Impeller Guard T (1) Bag *Self-Propelled Models Only. TOW BAR KIT- Standard with push models. (See figure 3) Optional with self-propelled models U (2) Hex Bolts 5/16-18 x 1.00" Long V (4) Shoulder Spacers w (2) Hex Nut 5/16-18 Thread X (1) Truss Machine Screw 1/4-20 x .75" Long Y (1) Lock Washer 1/4" I.D. z (1) Hex Nut 1/4-20 Thread AA (1) Shoulder Bolt AB (2) Belleville Washers 3/8" I.D. AC (1) Hex Jam Lock Nut 3/8-16 Thread (2) Tow Bar Halves (Not Shown) FIGURE 3 4 NOZZLE (N) FIGURE 4 1. Place nozzle (N) in position on front of housing so that it rests in flanges. Secure with one hand knob (F) and belleville washer (G). See figure 4. FIGURE 5 2. Place the upper handle (O) in position over lower handle. Fasten with four hex bolts (I) and lock nuts (J) provided. See figure 5. Two 7/16" wrenches are required. 3. Place the stud pins (K) in holes in upper handle (head of pins go to the inside of handle). Secure pins with push-on speed nuts (L) by holding speed nut with box wrench and tapping pin with hammer. See figure 6. 5 HAND KNOB (F) Place air duct assembly (P) over opening on top of housing. Secure with two hand knobs (F) and bellevilie washer (G). See figure 7. FIGURE 7 Assemble the bag by slipping the top straps on bag (T) over upper handle. Hook two small straps over stud pins on handle. Slip elastic opening of bag over air duct assembly. See figure 8. NOTE Be certain elastic on bag is placed over the flanges on air duct assembly. FIGURE 8 6. NOTE Steps 6, 7, 8 and 9 are for self-propelled units only. Assemble the clutch grip (A) to the left hand side of upper handle. Secure in place with clevis pin (C) and hair pin cotter (B). See figure 9. Head of clevis pin should be to the outside of handle. FIGURE 9 6 LOCK NUT (E) EXTENSION SPRING (D) \ CLUTCH ROD (Q) 7. Slide the extension spring (D) onto clutch rod (Q) as shown in figure 10. Thread lock nut (E) onto clutch rod approximately 2-1/2 inches. FIGURE 10 CLUTCH BRACKET ASSEMBLY 8. Hook top (hooked end) of clutch rod into clutch grip. Hook spring into clutch bracket assembly. See figure 11. Spring should not have any slack. Adjust nut so that when the clutch grip is all the way up, there is no slack in the spring. 9. Thread hex jam nut (M) onto clutch rod, and lock it against the lock nut (E). FIGURE 11 HAND KNOB ASSEMBLY INSTRUCTIONS To Convert from a Vacuum to a Leaf Blower. At WARNING t FIGURE 12 Engine must be stopped (off) and spark plug wire disconnected. 1. Remove the bag. 2. Remove the air duct assembly by removing two hand knobs and bellevilie washers. 3. Remove the nozzle by removing one hand knob and belleville washer. -4. Remove the hand knob and belleville washer holding the housing to engine brace. See figure 12. 7 I FIGURE 13 5. Lift up and out on the housing and rotate it 105° clockwise. Chute opening should be to the rigb" hand side when viewed from the front of uni See figure 13. 6. Place the impeller guard (S) into flanges on front of housing. Line up hole in guard with hole on housing. Secure with one hand knob, bellevilie washer and heavy flat washer (H). See figure 13. HAND KNOB D1RECTIOIV AL DISCHARG ASSEMBLY (R) 7. Place the directional discharge assembly (R) ovei chute opening. Secure with two hand knobs and bel levi I le washers. See figure 14. FIGURE 14 BELLEVILLE TRUSS WASHER (AB) BOLT (AA) / BELLEVILLE WASHER (AB) FIGURE 15 ASSEMBLY INSTRUCTIONS for Tow Bar Kit (Optional) 1. Remove the self-tapping screws on each side of frame. Refer to drawing on page 12, reference number 42. 2. Place tow bar half in position on frame. Place one shoulder spacer (V) between frame and tow bar. Next, place shoulder spacer (V) and hex bolt (U) through tow bar and frame. Secure with hex nut (W). See figure 15. Repeat for other side. 3. Secure the two tow bar ends together with truss machine screws (X), lock washers (Y) and hex nuts (Z). See figure 15. To attach the tow bar to a hitch, place the shoulde”'" bolt (AA) up through the tow bar. Place one bel levi IK washer (AB) on the shoulder bolt, then the hitch place and the other bel levi I le washer. Cupped side of the washers must b...