Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Finally, tighten the two bolts fastening the hitch brackets to the hitch tubes. 7. (Figure 4 or 5) Assemble the hitch pin (Y), two 3/4" spacers (U) and the 1/8" hair cotter pin (N) to the hitch brackets. 4 5/16" x 2" HEX BOLT (B) 5/16" HEX LOCK NUT (G) 3/4" SPACER (U) HITCH BRACKET HITCH BRACKET (STRAIGHT) 1/8" HAIR COTTER PIN (N) HITCH PIN (Y) CURVED HEAD BOLT (C) 5/16" HEX NUT (H) BOWED WASHER (L) 5/16" LOCK WASHER (K) HEIGHT ADJUSTMENT HANDLE GRIP 6 5 7 5/16" x 2" HEX BOLT (B) 5/16" HEX LOCK NUT (G) 3/4" SPACER (U) HITCH PIN (Y) HITCH BRACKET (STRAIGHT) 1/8" HAIR COTTER PIN (N) HITCH BRACKET ENGLISH 5/16" HEX LOCK NUT (G) 5/16" FLAT WASHER (J) HEIGHT ADJUSTMENT STRAP 5/16" x 3/4" HEX BOLT (F) SPACER BUSHING (T) ENGLISH ENGLISH 11. (Figure 8) Position the height adjustment handle side to side so that the tooth lock washer (M) can fit between the handle and the height adjustment strap. Tighten the nuts securing the height adjustment handle. 12. (Figure 8) Insert the 5/16" x 3/4" carriage bolt (E) through the height adjustment handle. Assemble onto the bolt, in order, the 5/16" tooth-lock washer (M), the height adjustment strap, a 5/16" flat washer (J) and the plastic knob. 5/16" FLAT WASHER (J) 8 5/16" x 3/4" CARRIAGE BOLT (E) TOOTH LOCK WASHER (M) PLASTIC KNOB 2. (Figure 10) Insert the two upper hopper side tubes through the stitched flaps on each side of the hopper bag. 3. (Figure 10) Assemble the ends of the rear hopper tube onto the ends of the upper hopper side tubes. Fasten together using plastic plugs (Z). UPPER HOPPER SIDE TUBE PLASTIC PLUG (Z) 10 4. (Figure 11) Turn the second rear hopper tube so that the brace holes in the middle of the tube face up. Assemble the ends of the rear hopper tube onto the ends of the lower hopper side tubes. Fasten together using ASSEMBLY OF HOPPER BAG plastic plugs (Z). 1. (Figure 9) Turn a rear hopper tube so that the brace holes in the middle of the tube face down. Slide the tube through the two loops sewn to the top rear seam inside the hopper bag. REAR HOPPER TUBE (brace holes on bottom) INNER BAG LOOPS 9 LOWER HOPPER SIDE TUBE PLASTIC PLUG (Z) REAR HOPPER TUBE (brace holes on top) 11 7 ENGLISH ENGLISH 5. (Figure 12) Place the assembled lower hopper tubes into the bottom of the hopper bag. 6. (Figure 12) Attach the ends of the lower hopper side tubes to the inside of the upper hopper side tubes using two 3/8" x 1/2" clevis pins (P) inserted from the inside, and two 3/32" hair cotter pins (O). 12 LOWER HOPPER SIDE TUBE HOPPER BAG BOTTOM UPPER HOPPER SIDE TUBE 3/8" x 1/2" CLEVIS PIN (P) 3/32" HAIR COTTER PIN (O) 7. (Figure 13) Insert the bag frame strap into the stitched sleeve along the front edge of the bag bottom. 8. (Figure 13) Assemble the bag frame strap to the lower hopper side tubes using two 1/4" x 1-1/8" clevis pins (Q) and 3/32" hair cotter pins (O). 9. (Figure 14) Secure the bag corners around the lower hopper side tubes by snapping the bag flaps to the bag bottom on both sides. SNAP FLAP 14 FIGURE 14 IMPORTANT: Do not over bend the support rods during the following step. Over bending will cause the steel rods to loose supporting tension. 10. (Figure 15) Tip the hopper onto it's back to assemble the two hopper support rods. Place the ends of each rod into the upper and lower rear hopper tubes, bending the rod just enough to fit into the holes in the tubes. SUPPORT RODS 15 13 1/4" x 1-1/8" CLEVIS PIN (Q) 3/32" HAIR COTTER PIN (O) BAG FRAME STRAP 8 14. (Figure 18) Secure the rope to the top center of the ENGLISH 11. (Figure 16) Feel along the stitched flap on the hopper bag to locate the lower hole in each upper hopper side tube. Pierce a hole through both sides of the stitched ENGLISH 11. (Figure 16) Feel along the stitched flap on the hopper bag to locate the lower hole in each upper hopper side tube. Pierce a hole through both sides of the stitched UPPER HOLE LOWER HOLE UPPER HOPPER SIDE TUBE flaps in alignment with the lower hole. 16 hopper bag frame. 18 17 LOWER HOLE 3/32" HAIR COTTER PIN (O) 3/8" x 3" CLEVIS PIN (S) BAG ARM TUBE VINYL CAP each bag arm tube. 19 BAG ARM TUBE 1/4" x 1-3/4" CLEVIS PIN (R) 3/32" HAIR COTTER PIN (O) ATTACHING SWEEPER HITCH TO TRACTOR (Figures 20, 21, 22) 1. Place the tractor and sweeper on a flat level surface. 2. Set the sweeper height adjustment handle to about the middle of its adjustment range. 3. Attach the sweeper hitch brackets to the tractor hitch, arranging the 3/4" spacers to make the bottom of the sweeper bag as level with the ground as possible. See figure 21 for tractor hitches that are 11" to 13" above the ground. See fi gure 22 for tractor hitches that are 8" to 11" above the ground. IMPORTANT: For best performance, the bottom of the sweeper bag should be as level with the ground as possible with at least 5" ground clearance. See figure 20. Tractor hitches with 8" to 11" ground clearance. 20 2221 Tractor hitches with 11" to 13" ground clearance. TRACTOR HITCH 8"-11" TRACTOR HITCH 11"-13" ENGLISH 5" Min. ......