Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
See figure 13. HINT: Push in on hex bolts as you tighten to form threads. 23. Connect the hose adapter to the engine housing by fastening three wing nuts to the pre-assembled bolts in the engine housing. See figure 13. 25. Place the hose hanger rod down into the hose hanger bracket on the impeller housing assembly. See figure 15. NYLON WASHERWING NUT5/16" X 3/4" HEX BOLT(SELF TAP) FIGURE 15 FIGURE 13 CLAMPHOSEHOSE ADAPTER(NOZZLE) 29. Assemble the hitch plate to the tractor hitch if: a. Your tractor has a square (straight) hitch frame, to help prevent binding. b. Your tractor has a lightweight hitch frame that needs reinforcement for towing. Use a 1/2" x 1-1/2" hex bolt, a 7/16" flat washer and a 1/2" lock nut. See figure 18. 26. Place a hose clamp onto the end of the hose. Push the hose onto the hose adapter (nozzle). Tighten the hose clamp onto the hose and hose adapter. Do not collapse the hose adapter when tightening the clamp. See figure 16. 27. The remaining hose clamp will be used later to fasten the hose to the deck adapter. TRACTOR HITCH FRAME (SQUARE) HITCH PLATETRACTOR HITCHFRAME (TAPERED) 1/2" x 1-1/2" HEX BOLT7/16" FLAT WASHER1/2" LOCK NUTATTACHMOW-N-VACHERE 25" TARP STRAP HOSE HANGER ROD FIGURE 18 FIGURE 16 28. Loop the 25" tarp strap under the hose. Fasten the hooks to the hose hanger rod. See figure 17. FIGURE 17 3. Slide the last lower support rod through outer edge of the cart cover. The bend in the rod must face in the direction shown in figure 21. ASSEMBLING CART COVER 1. Slide the front support tube through the double loops located near the front of the cart cover. See figure 19. BENDCART COVERSUPPORT ROD DOUBLE LOOPSFRONT SUPPORTTUBECART COVER FIGURE 21 FIGURE 19 PERFORM STEPS 4-6 IF YOU ARE USING SPRAY ADHESIVE (RECOMMENDED). IF YOU ARE NOT USING SPRAY ADHESIVE, SKIP TO STEP 7 ON PAGE 12. 4. Apply spray adhesive to the side of the top support angle shown in grey. Follow directions on spray adhesive for proper application. See figure 22. 5. Once the spray adhesive is tacky to touch, place top support angle inside of cart cover and fold the edges of the cover onto side of support angle with spray adhesive. See figure 22. 6. Wait until adhesive dries, securing support angle in place, before continuing to step 7. SPRAYADHESIVEFOLD EDGESTOP SUPPORT ANGLECARTBAG 2. Slide two of the lower support rods through the center loops located in the top of the cart cover as shown in figure 20. CENTER LOOPSUPPORTRODSCENTER LOOPCART COVER FIGURE 20 FIGURE 22 1/4" x 1-1/4" HEX BOLT1/4" LOCK NUT 7. Secure front support tube to top angle support using two 1/4" x 1-1/4" hex bolts and 1/4" lock nuts. DO NOT TIGHTEN YET. See figure 23. NOTE: Cart bag not shown for clarity. 9. Attach the second lower support rod to the outside and the third lower support rod to the inside of the top angle support using two 1/4" x 3/4" hex bolts and 1/4" lock nuts. DO NOT TIGHTEN YET. See figure 25. NOTE: Cart bag not shown for clarity. 1/4" x 3/4" HEX BOLT1/4" LOCKNUT2ND ROD3RD ROD FIGURE 23 FIGURE 25 10. Attach the braces to the front support tube using two 1/4" x 1-1/4" hex bolts and 1/4" lock nuts. DO NOT TIGHTEN YET. See figure 26. NOTE: Cart bag not shown for clarity. 8. Attach the lower support rod closest to front support tube to the outside of the top angle support using two 1/4" x 3/4" hex bolts and 1/4" lock nuts. DO NOT TIGHTEN YET. See figure 24. NOTE: Cart bag not shown for clarity. 1/4" x 1-1/4" HEX BOLT1/4" LOCKNUT 1/4" x 3/4" HEX BOLT1/4" LOCK NUT FIGURE 26 FIGURE 24 13. Slide each end of the rope through the holes in the tailgate shown in figure 28. 14. Tie a knot in the end of each side of the rope to secure the rope in place. Keep knot loose. See figure 28. HINT: Knot may need to be moved up or down in rope to secure tailgate. See step 18 for more information. 15. Slide tailgate into tailgate guides. 16. Attach clips to 3rd lower support rod and fasten them to the tailgate using two #10 x 5/8" slotted head bolts and #10 nuts. See figure 28. 17. TIGHTEN all bolts assembled in steps 7 through 12. 18. Secure tailgate rope around the bolts shown in figure 28. If rope does not keep tailgate held down or rope is too short to secure around bolts, move the knot up the end of the rope to loosen or down to tighten. Once knot is in desired location, tighten the knot to secure it in place. NOTE: Cart bag not shown for clarity. While performing the assembly operations in step 11, make sure the cart bag is between the top angle support and the cart. 11. Place the top angle support and cart bag ontop of the cart as shown in figure 27. Then, using a screwdriver or other sharp object, poke holes through the cart bag for the bolts that will be assembled in step 12. 12. Attach the top angle support and braces to the cart using seven 1/4" x 3/4" hex bolts, fourteen 5/16" washers (one placed on each side) and seven 1/4" nylock nuts. DO NOT TIGHTEN YET. See figure 27. NOTE: Cart bag not shown for clarity. #10-32 x 5/8" TRUSS BOLT...