1. Adjust height of vacuum inlet. For maximum debris pickup, inlet should be as close to debris as possible without blocking airflow and engine speed set to “FAST”. 2. Inspect debris bag. It must be properly attached to machine, in good condition, clean and dry with the top zipper fully closed. Make sure that the accessory plug is installed into front hole in vacuum nozzle. 3. Start engine. Not all debris pickup will require that the engine speed be set to “FAST”. You can experiment with vacuum

10 Service – Every 25 Operating Hours.......................................................................... 10 Storage – Out of Season.............................................................................................10 SECTION 4- ADJUSTMENTS AND REPAIR .................................................................. 11 Engine Adjustments & Repair .................................................................................... 11 Impeller Replacement..........................

No. Description 1694498 Clean Sweep Twin Catcher Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Table of Contents Safety Rules & Information General Warnings............................................2 Safety Decals ..................................................2 Storing the Grass Catcher...............................3 General Operating Information Before Operation .............................................3 Mowing with the Catcher .................................3 Required Accessories

Place two 5/16 x 1-1/2 long hex bolts with 5 /16 flat washers through the outside of the cart’s box and through the stake. b. Secure with two locknuts on the inside of the box. c. Install the two door hooks when bolting the rear stakes. Each door hook is bolted to the outside of the cart through the top stake bolt. The end of the hook is facing outward and toward the end of the cart. (DO NOT place the plastic caps over the top of the stakes at this time.) 4. Bolt swivel wheel to the H-frame.

NO. 1690990 Figure 1. A. Elbow B. Lockwasher, 1/4" C. Screw, 1/4-20 x 3 D. Hose, 6" ID E. Clamp F. Nut, 1/4" G. Clamp H. Clamp I. Capscrew, 3/8-16 x 2" J. Capscrew, 3/8-16 x 2-1/2" K. Hitch Extension L. Lockwasher, 3/8" M. Nut, 3/8" N. Housing O. Hose, 7" ID P. Nut, 1/4" Q. Lockwasher, 1 /4" R. Capscrew, 1/4-20 x 3/4 S. Tube Support T. Lockwasher, 1 /4" U. Nut, 1/4" V. Tube Support W. Capscrew, 1/4-20 x 3/4" X. Hitch A WARNING Do not operate the vacuum collector with any part

1700259. Located on Blower. I A warning! sn DO NOT OPEN COVER WITH ENGINE RUNNING. DO NOT OPERATE ENGINE WITHOUT COMPLETE CATCHER IN PLACE. Part No. 1676923. Located on Cart (Installed During Setup). A WARNING DO NOT USE THIS HOLE FOR DRAWBAR. TRACTOR TIP OVER MAY OCCUR. Part No. 1700346. Located on Bracket (Installed During Setup). OPERATORS MANUAL MOWER DRIVEN VACUUM COLLECTOR BLOWER ASSEMBLY MFG. NO. 1691260 CART COLLECTOR MFG. NO. 1691187 MFG. NO. 1691320 file 1'^' FORM - 1679

Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT SAFETY INSTRUCTIONS on Pages 2 & 3 of this manual and All SAFETY messages on the machine and its attachments before operating. 2.2.2 NOMENCLATURE The nomenclature picture above, Figure 1.1, shows the essential parts of the Yard Vacuum. It is recommended that all operators of this equipm

6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container, rather than a gasoline dispenser nozzle. 8. DO NOT start gas powered equipment in enclosed vehicles or trailers. 9. Keep the nozzle in contact with the rim o

No. SV25550HC SV25650B 7085638 7085687 Model Mfg. No. SV25500HV SV25550HV 7085644 7085642 COMMERCIAL MODELS Before operating your new machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense! NOTE: Specifications are correct at time of printing and are

Zeeb Road • Dexter, MI 48130 (734) 996-9116 • FAX (734) 996-9014 1-800-456-7100 251-3845, 7/04 51-3845, 7/04 Table of Contents Section 1 ... Operation and Maintenance Section 2 ... Service Section 3 ... Parts Section 4 ... Appendix 51-3845, 7/04 51-3845, 7/04 Operation and Maintenance M26 Series Table of Contents Introduction .............................................................. 7 Safety .................................................................... 6-12 General Safety Information