Avoid mounting locations that subject the bracket to breaking waves. Avoid mounting locations that do not provide protection from harmful UV rays of the sun. The bracket must be mounted facing inboard to avoid being lost overboard due to impacts of breaking waves, personnel or loose gear. Visually inspect the area surrounding the mounting bracket installation site for hidden hazards or obstacles that may have been overlooked during the location selection. If there is any doubt as to the ready ac

Turning off the beacon If your beacon was manually activated and you wish to deactivate, return the thumb switch to the “OFF” position. If automatically activated and you wish to deactivate, remove the beacon from the water and dry the unit or place the beacon back into the release bracket. The beacon normally takes up to 12 seconds to deactivate. If deactivation should fail, remove the four screws holding the unit together and unplug the battery to disable the unit. Return the beacon to ACR Ele

The 121.5 MHz signal is used by SAR to home in on the beacon as they approach it. The 406 MHz signal is detected by multiple satellites and from that information the location of the beacon can be calculated. This data alone is sufficient for SAR to find persons or ships in distress in a reasonable timeframe. 2. Anatomy of your beacon NOTE: When unpacking your beacon, it is recommended that you save the original packaging for re-use when shipping the beacon for battery replacement in the future.

A OWNER VESSEL RADIO CALL SIGN UIN # CAUTION: Before proceeding to install, test or use your new ACR Electronics’ product, please read this Product Support Manual in its entirety. If you have questions regarding the contents of the manual, please contact our Technical Service Department at ACR Electronics, Inc., Telephone +1 (954) 981- 3333. Please be ready to provide the technician with the page number you wish to discuss. If you have a question that is not covered in the manual, please visit o

Figure 5 - Belt Clip . 5.1 Multi-Function Belt Clip The MicrOFix™ comes standard with a multi-function belt clip. To install the clip, simply align the bottom tabs on the clip with the insert holes located on the bottom of the beacon. Snap the clip in place by pressing the top of the clip so that the two top tabs engage in the two insert holes on the top of the beacon (see figure 5). To remove the clip, push up and back on the top tabs one at a time to disengage the clip from the beacon. The Mic

If the internet is not accessible to you, complete the enclosed registration form. Do not confuse this with the ACR Electronics warranty card. Mail with the pre-addressed, postage paid envelope to: NOAA SARSAT Beacon Registration NSOF, E/SP3 4231 Suitland Road Suitland, MD 20746 C. Faxing your registration is also acceptable. Fax the registration form to fax # +1 (301) 817-4565. Note that the information you provide on the registration form is used only for rescue purposes. Complete and send the

C Manual Footer In the United States WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. WARNING: This product is a supplemental navigation tool only! The user assumes all responsibility associated with the use of this device and safe navigation. It is important to understand that all vessels may not be equipped with AIS transponders and the

Use the antennas supplied with this kit. The VHF antenna supplied for use with the Nauticast™-B is omni-directional, vertically polarized with unity gain (0 dB) and a band width sufficient to maintain VSWR <1.5 over the frequency range 156–163 MHz. As a minimum the 3dB bandwidth will cover the two AIS channels and the DCS channel. The antenna is also suitable for marine shipboard applications (index of protection, ruggedness, means of mounting, etc.). If you elect to not use the antenna supplied

Antenna is spring loaded and deploys rapidly. The release trigger holds the antenna down at the beacon’s side in the stowed position. When the beacon is switched to the “ON” position the antenna will spring into an upright position. The antenna should then be extended to its full length for optimum transmission performance. The beacon should be operated in an area free of obstructions. 3.2 MANUAL ACTIVATION The beacon is manually activated. Manually activating the beacon requires movement of the

2766.6 ETSI Type Approved to ETS 300 152 Y1-03-0167 Rev. B ACR Electronics, Inc. 5757 Ravenswood Road Fort Lauderdale, Fl 33312 Tel : +1(954) 981-3333 Fax: +1 (954) 983-5087 Email: Info@acrelectronics.com * * * WARNING * * * THIS TRANSMITTER IS AUTHORIZED FOR USE ONLY DURING SITUATIONS OF GRAVE AND IMMINENT DANGER DELIBERATE MISUSE MAY INCUR A SEVERE PENALTY Foreword: Congratulations and thank you! You have just purchased the finest Class B personal EPIRB available on the market. Other brands me