Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Important! Please follow these instructions. This kit may be different from the one specified in instruction booklet. COMBINATION 8X8 and 10X8 FLOOR KIT This floor kit will build either the 10’ wide or 8’ wide x 7’ 8-5/8” deep floor size FOR MARCO SERIES, SOLAR SHED AND MWP IMPERIAL ONLY This floor kit is for 10’ x 7’ 8-5/8” and 8’ x 7’ 8-5/8” buildings. Please refer to the appropriate pages of this instruction manual to build the floor size needed. If constructing an 8X8 storage building, you will have additional material which can be used to construct a shelf (some cutting required) or other projects. - BEFORE Y OU BEGIN - • First... Read these instructions thoroughly before you begin assembly. Assembly is easiest if you follow the steps in the order shown. Lumber is graded from only one side. Check the part for the most attractive face and make sure to face it to the outside. • Check all parts Compare parts you have to the list on page 2. If a part is missing, circle the part in question in the parts list and call us toll-free at 1-800-437-0784. • Assistance required We recommend that you assemble this floor on level ground in the location it will be used. Assistance is necessary to handle, fit, and secure some components. Two people maybe needed for some steps. • Squareness is very Important! Keeping all 90° corners and 90° perpendiculars square throughout the assembly of this floor kit will make each succeeding step easier and is necessary to assure that all components fit together properly. • Check local zoning Before starting construction, check with your local building code official for any required permits, variances, etc. • Check floor kit size Before starting construction on your floor, make sure that you check in the instruction manual to ensure that you are building the correct size floor kit for your building. Always wear OSHA-APPROVED safety glasses throughout assembly process #16628 ¦ Tools required . Hammer . Level . Pencil . Tape Measure ¦ Optional tools . Chalk Line . Square . Nail Pouch . Saw 8x8 See pages 2-3-4 10x8 See pages 5-6 1 Parts Needed: Parts Needed: A C D F 2 - 48x92-5/8x5/8" Floor Panels 5 - 2x4x89-1/2" Floor Joist FOR 8X8 BUILDINGS 2 - 2x4x72" Bond Boards 2 - 2x4x24" Bond Boards ACTUAL SIZE 96” WIDE x 92-5/8” DEEP -2" and 3" Nails NOTE: Part letters are Not stamped on floor kits. ASSEMBLY OF 8’ x 92-5/8” FLOOR FRAME IMPORTANT! If you will be storing heavy items (such as lawn tractor, motorcycle, snowmobile etc.) we recommend you upgrade from 24” on center (61 cm) to 12” on center (30.5cm) floor framing. This requires you to add the following material: • Qty. (4) of 2”x 4”x 89-1/2” (5 x 10 x 227 cm) Treated • 16 ea. 3” (7.6cm) galvanized nails A (2) 3" Nails 24" (61 cm) 24" (61 cm) 24" (61 cm) 24" (61 cm) 92-5/8" (4) 3" Nails at Joint 96" (244 cm) Center of Stud Center of Stud C C C D C C D D D F F F A: Position Floor Joists 89-1/2”, Floor Bond Boards 72”, and Floor Bond Boards 24” as shown. Using 3” nails, nail twice through each Bond Board & into each end of each Joist , keeping pieces flush at top and ends, and maintain 24” spacing. Where & join together use 4-3” nails. C D F D F C D F B B: Completed Floor Frame should be positioned at building site, leveled, using shims between floor frame and ground before proceeding to Floor Panel Attachment. Square frame by making corner-tocorner measurements (X to X and Y to Y) the same. Y Y X 2 8X8 FLOOR KIT INSTRUCTIONS CONTINUED A 8X8 FLOOR KIT INSTRUCTIONS CONTINUED A FLOOR PANEL ATTACHMENT: C: Position a 48 x 92-5/8” Floor Panel flush to the outside edges of sides and back of Floor Frame. Secure panel with two 2” nails at outside corners and one 2” nail at other corners. C C D A F 92-5/8" D: Position the other 48” x 92-5/8” Floor Panel A flush against first panel and flush to edges of Floor Frame. Secure panel with two 2” nails at outside corners and one 2” nail at each of other corners. With Floor Panels flush to outside edges of Floor Frame, nail with 2” nails every 12” through Floor Panels into all Floor Bond Boards C D & and Floor Joists . F Note: Mark a line on the Floor Panel over the center of each Floor Joist @ 24” using a pencil and a piece of lumber from the kit (or use a chalk line) to make nailing easier. Your Floor is now complete. Check to be sure it is properly positioned and leveled to ground before beginning assembly of your Handy Home Wooden Storage Building. 96" Nails every 12" (30 cm) through Floor Panels into all Floor Bond Boards and Floor JoistsD AA 24" (61 cm) 24" (61 cm) F D 3 Parts needed to cut: B C E Parts needed to cut: B C E 1 - 23-7/8x92-5/8x5/8" Floor Panel 1 - 2x4x89-1/2" Floor Joist 8X8 OPTIONAL SHELF INSTRUCTIONS 2 - 2x4x48" Bond Boards -2" and 3" Nails (1) - 89-1/2" Board cut down to 88" (2) - 48" Board cut down to 2 (1) - 23-7/8x92-5/8" Panel cut down to 23-7/8x89-1/2" 24-11/16" 23-3/16" E B B E C C A Cut Cut Cut pieces of 24-11/16 and 23-3/16" SHELF PARTS TO CUT: A: Cut the 89-1/2” Board down...