Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Because the SRU 4010 may use different signals for each brand and even for different models of the same brand, it is advisable to test whether your TV responds to the SRU 4010. The example below instructs you how to do this. 1 Turn your TV on manually or use the original remote control.Tune to channel 1. 2 Check whether all the keys are working. For an overview of the keys and their functions, see ‘3. Keys and functions’. - If the TV responds as it should to all of the key commands the SRU 4010 is ready for use. • If the TV does not respond at all or not to all of the key commands, follow the instructions under Getting the remote control*, or for online setup go to: Setting the remote control This is only necessary if your TV does not respond to the SRU 4010. If that is the case, the SRU 4010 does not recognize the brand and/or model of your TV and you need to program the remote control to do so. You can set the remote control either automatically or manually. 4 Instructions for use Manually setting the remote control 1 Turn on the TV manually or use the original remote control.Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. On our website you can directly select your device typenumber to find the right code. 3 Use a pen or paper clip to press the Setup key and keep it pressed for 5 seconds until the Standby key blinks twice and then remains lit. Then enter the code noted in step 2, using the digit keys. The Standby key will now blink twice. If the key blinks once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. 5 Point the SRU 4010 at the TV and check that it responds as it should. - If the TV responds to all of the key commands, the SRU 4010 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. Automatically setting the remote control The remote control will now automatically search for the right code for your device. 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). 2 Use a pen or paper clip to press the Setup key and keep it pressed for 5 seconds until the Standby key blinks twice and then remains lit. 3 Press the Standby key of the SRU 4010 and keep it pressed. The SRU 4010 now starts emitting all known ‘TV off’ signals, one by one. Each time a code is sent, the Standby key lights up. 4 5 English English Instructions for use 4 When your TV switches off (stand-by), immediately release the Standby key of the SRU 4010. - The SRU 4010 has now found a code that works on your TV 5 Check if you can operate all functions on your TV with the SRU 4010. If this is not the case, you can redo the automatic setting. The SRU 4010 will then search for a code that works better. After the SRU 4010 has run through all the known codes, the search will stop automatically and the Standby key stops blinking. Automatic programming of a TV takes a maximum of 6 minutes. 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. © y Standby........switches the TV on or off @ Setup............selects setup mode. @ Red, green, yellow and blue fasttext keys. (?) MENU /q..... . . - switches teletext on/off - pressed together with SHIFT ©: opens the TV menu. A/V / S...... . . . . - mutes the sound of the TV - pressed together with SHIFT ©: selects external Audio/Video inputs, connected to the SCART connector(s) of your equipment (A/V function). OK / EB..........- selects wide screen TV (16:9). - pressed together with SHIFT ©: confirms your selection. BACK / O.......- jumps back one level in the menu ortums off the menu. - switches text TV off. © - VOL +..........- adjusts the TV volume. - pressed together with SHIFT ©: cursor left, right in a menu. © Digit keys........direct choice of channels and tracks. © SHIFT....... . . . . for extra functions.When pressed at the same time as a second key, the second key will get another function.All blue labelled keys can be used together with SHIFT. For example: SHIFT + 2.......opens electronic TV program guide. SHIFT + o......enters TV menu. Try out other combinations with the SHIFT-key on your device in order to find out which functions are available. Only functions featured on the original remote control are available. © -/--...............selects between one- and two-figure channel numbers. © - PROG +..... . . . - selects a previous or following channel / program. - pressed together with SHIFT ©: cursor up, down in a menu. If the device does not respond at all, or not to all of the key commands, follow the instructions under eSe...
Este manual também é adequado para os modelos :Controle remoto - SRU4010/10 (383.62 kb)