Assessments - 4, GPA: 4.3 ( )

Fabricante : Genie Arquivo Tamanho: 696.71 kb Arquivo Nome : Língua de Ensino:

Do not stand or sit on the forks, load platform or boom. Do not climb on the machine. Tip-over Hazards Do not exceed the rated load capacity. See Load Capacity Charts section. Do not raise the load unless the leg lock pins have been properly inserted into the legs. Do not raise the load unless the correct length legs are properly installed. Do not raise the load unless the machine is on a firm, level surface. Do not move the machine with a raised load, except for minor positioning. Do not tilt the machine back with a raised load. Do not use blocks to level the machine. Do not operate the machine in strong or gusty winds. Increasing the load surface area will decrease machine stability in windy conditions. Do not place ladders or scaffolding against any part of the machine. Do not operate the machine unless the wheel/ leg /caster configuration is properly installed. Prior to use, check the work area for drop-offs, holes, bumps, debris, unstable or slippery surfaces or other possible hazardous conditions. Avoid debris and uneven surfaces while rolling a machine without the legs installed. Do not replace machine parts critical to stability or structure with items of different weight or specification. Do not cause a horizontal force or side load to the machine by raising or lowering a fixed or overhanging load. Do not use the machine on a moving or mobile surface or vehicle. Collision Hazards Do not raise if the load is not properly centered on the forks or load platform. Check the work area for overhead obstructions or other possible hazards. Do not stand under or allow personnel under the machine when the load is raised. Do not lower the load unless the area below is clear of personnel and obstructions. Use common sense and planning when transporting the machine on an incline, slope or stairs. Maintain proper lubrication on the frame channels. See the Pre-operation Inspection section. Unlubricated frame channels can bind or stop moving, which could result in the load shifting or falling. Genie Lift Part No. 35566 First Edition • Sixth Printing Operator's Manual Electrocution Hazards This machine is not electrically insulated and will not provide protection from contact with or proximity to electrical current. Maintain safe distances away from electrical power lines and apparatus in accordance with applicable governmental regulations and the following chart. Voltage Minimum Safe Approach Distance Phase to Phase Feet Meters 0 to 300V Avoid Contact 300V to 50KV 10 3.1 50KV to 200KV 15 4.6 200KV to 350KV 20 6.1 350KV to 500KV 25 7.6 500KV to 750KV 35 10.7 750KV to 1000KV 45 13.7 Allow for mast movement and electrical line sway or sag, and beware of strong or gusty winds. Keep away from the machine if it contacts energized power lines. Personnel must not touch or operate the machine until power lines are shut off. Do not use the machine as a ground for welding. Bodily Injury Hazards Do not grasp the cable. Keep hands and fingers away from the pulleys, carriage and other potential pinch points. Do not place arms, hands or fingers through the frame. SAFETY RULES Improper Use Hazard Never leave a machine unattended with a load. Unauthorized personnel may attempt to operate the machine without proper instruction, creating an unsafe condition. Damaged Machine Hazards Do not use a damaged or malfunctioning machine. Do not use a machine with a worn, frayed, kinked or damaged cable. Do not use a machine with less than 4 wraps of cable on the winch drum when the carriage is fully lowered. Conduct a thorough pre-operation inspection prior to each use. Be sure that all decals are legible and in place. Maintain proper lubrication on the winch. See Genie Lift Parts and Service Manualfor details. Do not allow oil or grease on braking surfaces. Crushing Hazard Maintain a firm grasp on the winch handle until the brake is locked. The brake is locked when the load will not cause the winch handle to turn. Lifting Hazard Use proper lifting techniques to load or tip the machine, or move the machine on stairs. Do not move the machine on stairs when the machine is equipped with the 4 point caster option. Part No. 35566 Genie Lift Operator's Manual First Edition • Sixth Printing SAFETY RULES Ladder Safety Fall Hazards Do not use the ladder as scaffolding. Do not sit on the ladder. Do not over reach. Keep your body centered between both side rails. Do not use the top rung as a step. Tip-over Hazards Do not exceed the ladder's maximum capacity of 250 lbs / 113 kg. Do not overload the ladder. Ladders are designed for 1 person only. Do not use the ladder unless it is properly set up. Do not shift the ladder while on it. Avoid pushing or pulling off to the side of the ladder. Do not set up the ladder on slippery surfaces. Do not use blocks to level the ladder. Electric Winch Safety Electrocution Hazard Do not operate the DC battery charger unless using a 3-wire grounded extension cord connected to a grounded AC circit. Do not alter or disable...

Baixe o seu

Para fazer o download, introduza 2 dígitos :