Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
See figure 15. 2. To lower the power seat, press and hold the lower part of the switch. Release the switch when you have attained your desired height or until reaching the lowest position. NOTE: The PMV must be stopped in order for the power seat to be operated. If the power seat switch is pressed while the PMV is in motion, the PMV will slow and come to a stop. The PMV may also produce a fault code indicated by the Status LED on the console. If a fault code occurs, you will need to turn the PMV’s power off then back on again before proceeding. 400/181 THROTTLE CONTROL LEVER Figure 14. Power Seat Switch (With Vertical Line And Circle) Used In Conjuction With Throttle Control Lever to Activate The Power Seat Actuator (Switch Shown In The “Off” Position) Figure 15. Power Seat Switch (With No Markings)-Activates The Power Seat Actuator Hurricane 34 Hurricane I X . D I S A S S E M B LY A N D A S S E M B LY DISASSEMBLY You can disassemble the PMV into seven pieces: the seat, the front section, the rear section, the rear shroud, the basket, and the batteries. See figure 14. No tools are required to disassemble or assemble your PMV. Since the disassembled sections of the PMV take up more floor space than the assembled unit, place the PMV on a level, dry surface with sufficient room to move the parts around. You will need about five feet in all directions. keep in mind that you may need assistance to lift some of the PMV components. 1. Place the manual freewheel lever in the drive position. 2. Lift the seat up and off the PMV. 3. Gently pull the shroud up and off of the rear section of the PMV. 4. Disconnect the battery strap. 5. Unplug both T-handle battery harnesses. See figure 17. 6. Remove the batteries. 7. Unplug the front-to-rear harness. See figure 17. WARNING! Failure to unplug both Thandle battery harnesses and the frontto- rear harness prior to separating the front and rear sections could result in permanent damage to the PMV. WARNING! Lifting weight beyond your physical capability may result in personal injury. Ask for assistance when necessary while disassembling or assembling your PMV. SEAT REAR SHROUD REAR SECTION BATTERIES BASKET FRONT SECTION Figure 16. The Hurricane Disassembled Figure 17. Harness Connections FRONT-TO-REAR HARNESS T-HANDLE BATTERY HARNESS T-HANDLE BATTERY HARNESS Hurricane 35 I X . D I S A S S E M B LY A N D A S S E M B LY Toggle Latch Release 1. Push in the toggle latch release button while pulling back the toggle latch. See figures 16 and 18A. 2. Position the toggle latch buckle over the top of the toggle latch. See figure 18B. TOGGLE LATCH TOGGLE LATCH RELEASE BUTTON Figure 18. Toggle Latch (Latched) Figure 18B. Buckle Secured ASSEMBLY 1. Position the front and rear sections of your PMV as shown in figure 21. 2. Align the lower slots of the front section with the corresponding pegs on the front of the rear section. See figure 21. 3. Holding the seat post, slowly pivot the rear section forward until the curved locking brackets are fully connected onto the top rear pegs. See figure 19. 4. Raise the tiller. WARNING! Position the front-to-rear harness so it won’t become pinched between the frame halves when pivoting the rear section forward. See figure 21. Figure 21. Frame Sections Frame Separation 1. Lower the tiller to the PMV floorboard. 2. Push back on the seat post to pivot the PMV’s rear section rearwards until the rear section is standing vertically on its bumper. See figure 19. 3. Lift the front section up until the lower pegs are no longer in the slots. See figure 20. 4. Carefully move the front section away from the rear section. Figure 19. Frame Positioning Figure 20. Separating The Frame Sections FRONT-TO-REAR HARNESS 5. Latch the toggle latch. See figure 18A. .. Lower the toggle latch buckle. .. Push back on the toggle latch so it locks into place. 6. Reinstall the batteries into the battery wells and reconnect the battery strap. 7. Connect the front-to-rear harness and both T-handle battery harnesses. 8. Reinstall the shroud. 9. Reinstall the seat, and lock it into place. Figure 18A. Toggle Latch (Unlatched) TOGGLE LATCH BUCKLE CURVED LOCKING BRACKET PEG PEG SLOT X . B A S I C T R O U B L E S H O O T I N G X. BASIC TR OUBLESHOO TING Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge. DIAGNOSTIC FLASH CODES The diagnostic flash codes for your PMV are designed to help you perform basic troubleshooting quickly and easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below develops. NOTE: Your PMV will not run unless the flash code condition is resolved and the PMV has been turned off, the...