Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
1081003) provided with the Bath Lift, contact a healthcare professional, dealer or technical personnel before attempting to install this kit, otherwise, injury or damage may occur. This kit MUST be installed by an Invacare Dealer or technical personnel. INSTALLATION WARNINGS After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. Use proper lifting techniques to avoid injury. Keep back straight and bend knees when lifting components of the bath lift. . . !"# $%&# $ . WARNING To prevent pinching injury between seat back and motor shroud when removing/ installing the seat, DO NOT grasp seat anywhere other than at the recess at the top (DETAIL "C"), the opening at the bottom of the seat or the lip at the top of the seat. To prevent frame from tipping when removing seat, either suction the frame to the floor or place one foot on the frame base when removing/installing the seat. CAUTION The bath lift seat MUST be removed from the top of the lifting cycle, otherwise, damage to the unit may occur. DO NOT grasp seat by side flaps, otherwise damage to the bath lift or the bathtub may occur. Seat DETAIL "C" Recess STEP 4 Spring Loaded Chair Release Button LIFT THE SEAT Slide Block STEPS 5-6 Groove Frame Seat Bottom FIGURE 1 - REMOVING THE SEAT NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact your Dealer for further instruction. SAFETY SUMMARY The following recommendations are made for the safe replacement of the PENDANT/CABLE/CURRENT LIMIT DEVICE: GENERAL WARNINGS REPLACING THE PENDANT/CABLE/ CURRENT LIMIT DEVICE NOTE: Refer to theINSTALLATION WARNINGSin the SAFETY SUMMARYof this instruction sheet. Removing the Seat (FIGURE 1) 1. Secure the frame to the floor with the suction cups or by standing on the frame base during removal of the seat. 2. Press the UP button on the pendant to raise the seat all the way up (DETAIL "A"). 3. Grasp the handgrip on the battery pack and pull upwards to remove it from the motor shroud as shown in DETAIL "B". 4. Press and hold the spring loaded chair release button to release the seat (DETAIL "C"). 5. While holding the button with one hand, grasp the seat bottom firmly with your other hand. 6. Slide the seat up until the slide block disengages from the groove in the frame as shown in FIGURE 1. 7. Grasp the handgrip on the battery pack and push downwards to install onto the motor shroud. 8. Press the DOWN button on the pendant to lower the bath lift to the lowest position (DETAIL "A"). 9. If necessary, remove the bath lift frame from the bathtub. Refer to REMOVING THE FRAME FROM THE BATHTUB in this instruction sheet. DETAIL "A" DETAIL "B" STEPS 1 AND 8 STEPS 2 AND 7 PULL UP TO REMOVE Down Button . PUSH DOWN TO Pendant Up Button INSTALL Handgrip Motor Shroud Battery Pack 1 ALWAYS lower the bath lift frame to the lowest position BEFORE performing this procedure. Otherwise, the bath lift frame may tip during installation resulting in injury and/or damage. CAUTION ALL water MUST be drained from the bathtub BEFORE removal of the bath lift frame to prevent damage to the bath lift frame or suction cups. ALWAYS release the suction cups from bathtub bottom BEFORE removing frame to prevent damage to the frame or bathtub. Removing the Frame from the Bathtub (FIGURE 2) WARNING 1. Remove the seat, if not already done. Refer to REMOVING THE SEAT in this instruction sheet. NOTE: Ensure bath lift is in lowest position before proceeding. 2. Grasp the handgrip on the battery pack and pull upwards to remove it from the motor shroud. 3. Tilt the frame forward towards the drain or gently pull up on the suction cup loops to release the suction cups from the bathtub. 4. Remove the frame from the bathtub. 5. Remove the motor shroud. Refer to REMOVING THE MOTOR SHROUD in this instruction sheet. Suction Cup Bathtub TILT FRAME FORWARDSFrame Suction Cup Loop FIGURE 2 - REMOVING THE FRAME FROM THE BATHTUB Removing the Motor Shroud (FIGURES 3 AND 4) WARNING ALWAYS lower the bath lift frame to the lowest position BEFORE performing this procedure. Otherwise, the bath lift frame may tip during installation resulting in injury and/or damage. WARNING ALWAYS remove the bath lift from the bathtub BEFORE performing this procedure. Otherwise - injury or damage may occur. 1. Remove the bath lift frame from the bathtub, if not already done. Refer to REMOVING THE FRAME FROM THE BATHTUB in this instruction sheet. 2. Remove the mounting screw, two (2) self-locking screws and three (3) washers securing the motor shroud to the bath lift frame. Refer to FIGURE 3. Self-Locking Screws (STEP 2) Mounting Screw (STEP 2) Washer (STEP 2) Washers (STEP 2) Motor Shroud (STEP 3) FIGURE 3 - REMOVING THE MOTORSHROUD CAUTION The motor shroud is still connected to the motor by the spade connectors and pendant cable. DO NOT attempt to forcibly separate the motor shroud from the motor. Otherwise - damage to the m...