1. Shut off the pump or sprayer. 2. Trigger the gun. 3. Open the gun air valve. 4. Disconnect the power source. Grounding To reduce the risk of electric shock, proper electrical grounding is essential. See your separate pump or sprayer instruction manual, and consult your local electrical codes for detailed grounding instructions. Working Pressure To reduce the risk of component rupture and serious bodily injury, never exceed 100 psi (7 bar) AIR OR FLUID WORKING PRESSURE to this gun. Do not exce

. Model Numbers Automatic Husky 750, 3/4-in Surge Suppressors Polypropylene Wetted Bottom Housing and Non-Wetted Top Housing 239096 with Buna–N bladder 239121 with PTFE bellows 239122 with fluoroelastomer bladder Stainless Steel Wetted Bottom Housing and Non-Wetted Top Housing 239095 with Buna–N bladder 239123 with PTFE bellows 239124 with fluoroelastomer bladder Automatic Husky 2000, 2-in Surge Suppressors Stainless Steel Wetted Bottom Housing, Polypropylene Non-Wetted Top Housing 239093 with B

Dampening effect of surge suppressor is not sufficient. Surge suppressor installed incorrect distance from pump Surge suppressor should be installed within 10 pipe diameters of pump discharge. Improper pressure charge See Charging and Startup, page 8. Surge suppressor pressure should be 2 to 10 psi (0.01 to 0.07 MPa, 0.1 to 0.7 bar) lower than system pressure. Surge suppressor does not hold pressure charge. See surge suppressor does not hold pressure in PROBLEM column. Failed bladder or bellows

Consult your fluid supplier to determine the conductivity or resistivity of your fluid. . If there is any static sparking or you feel an electric shock while using this equipment, stop pumping immediately. Do not use the equipment until you identify and correct the problem. . Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being pumped. . Pipe and dispose of the exhaust air safely, away from all sources of ignition. . Keep the work area free of de

2. NOTE: When you mount a plastic surge suppressor, do not overtighten by using a large pipe wrench near the threads of the fluid inlet. The housing may crack if tightened too much. Hand tightening is recommended. Connecting Automatic Models Connecting Manual Models . Connect the 1/4-in air supply hose to the 1/4 npt connection on the top of the surge suppressor. . Connect the 1/4-in air supply hose to the brass one-way check valve on the top of the surge sup. The air pressure to the surge suppr

. Do not exceed the maximum working pressure of the lowest rated component in your system. This equipment has a 120 psi (0.8 MPa, 8 bar) maximum working pressure and 120 psi (0.8 MPa, 8 bar) maximum incoming air pressure. . Solvent Compatibility: – Use fluids and solvents which are compatible with the equipment wetted parts. – Use only compatible solvents to clean all plastic parts. Many solvents can degrade plastic parts to the point where they could fail. Refer to the Technical Data section of

Les parties reconnaissent avoir convenu que la redaction du presente document sera en Anglais, ainsi que tous documents, avis et procedures judiciaires executes, donnes ou intentes a la suite de ou en rapport, directement ou indirectement, avec les procedures concernees. Graco Information For the latest information about Graco products, visit TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you: Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax:

. Parts Matrix Replacement Parts for Husky 750 and Husky 2000 Surge Suppressors, Series A Parts NOTE: The quantity of every part in this list for X’is isis 1 11 for every everyevery model modelmodel . The TheThe X’s ss indicate indicateindicate the thethe parts that are included in each model. Ref No. Part No. Description Surge Suppressor Models Automatic Husky 750 Automatic Husky 2000 Manual Husky 750 Manual Husky 2000 2 3 9 0 9 5 2 3 9 0 9 6 2 3 9 1 2 1 2 3 9 1 2 2 2 3 9 1 2 3 2 3 9 1 2 4 2 3

. . . . . . . . . . . . . . . . . . . 13 Parts Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . 18 Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Warning Symbol WARNING This symbol alerts you to the possibili

. Parts Matrix Replacement Parts for Husky 750 and Husky 2000 Surge Suppressors, Series A Parts NOTE: The quantity of every part in this list for X’is isis 1 11 for every everyevery model modelmodel . The TheThe X’s ss indicate indicateindicate the thethe parts that are included in each model. Ref No. Part No. Description Surge Suppressor Models Automatic Husky 750 Automatic Husky 2000 Manual Husky 750 Manual Husky 2000 2 3 9 0 9 5 2 3 9 0 9 6 2 3 9 1 2 1 2 3 9 1 2 2 2 3 9 1 2 3 2 3 9 1 2 4 2 3