Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
If adjustments are needed, refer to the engine manual packed with your shredder. 8 LUBRICATION WHEELS - The wheels require no lubrication. ENGINE - Follow engine manual for lubrication instructions. MAINTENANCE ^^CAUTION Always stop engine and disconnect spark plug wire before performing any maintenance. CUTTING BLADE The blade may easily be removed for grinding or replacement as follows: 1. Remove guide extension assembly by removing four elastic lock nuts (Ref. No. 11). See page 10. 2. Remove bolt (Ref. No. 38), lock washer (Ref. No. 37) flat washer (Ref. No. 36) which holds blade (Ref. No. 45), and blade retainer (Ref. No. 48) to engine crankshaft. See page 10. ■^NOTE Blade is reversible and can be assembled to crankshaft with either side showing. When sharpening blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the unit. Upon reassembly, make certain all parts are assembled properly and tightened securely. FLAILS AND FINGERS The flails and fingers can be reversed when they become dull. ENGINE OIL 1. Change oil in crankcase after first two (2) hours of operation. Then change oil every twenty-five (25) operating hours or sooner if equipment is operated in extremely dusty or dirty conditions. Unscrew oil drain plug located on the side at the bottom of the engine (see figure 15). Always tip engine towards oil drain hole. Be sure oil drains completely. Replace oil drain plug and refill with oil as directed on page 6. FIGURE 15 2. Check oil every five (5) operating hours or each time equipment is used. Add oil as necessary to keep level full to point of overflowing. CLEAN ENGINE Clean cylinder fins and underside of tank or housing thoroughly of all accumulated grass and debris. This is an aircooled engine which operates most effeciently when the cooling fins are clean. AIR CLEANER The air cleaner prevents damaging dirt, dust, etc. from entering the carburetor and being forced into the engine and is important to engine life and performance. To service air cleaner, refer to the engine manual packed with the shredder. NEVER RUN YOUR ENGINE WITHOUT AIR CLEANER COMPLETELY ASSEMBLED. OFF-SEASON STORAGE In event engine is to be stored for any length of time (30 days or more), prepare as follows: 1. Drain gasoline by tipping or syphon hose, then run engine until remainder is used and tank and carburetor are empty. m CAUTION Drain into container outdoors away from fire or flame. 2. Protect the inside of engine for storage by removing spark plug and pouring one ounce of SAE 30 oil through spark plug hole into cylinder. Crank engine, without starting, several times to spread oil over cylinder walls. 9 I MODEL 650 10 MODEL 650 PARTS LIST FOR MODEL 650 SHREDDER Ref. No. Part No. Color Code DESCRIPTION New Part Ref. No. Part No. Color Code DESCRIPTION New Part 1 11476 -452 Door-Chip-lt 32 736-0192 FI-Wash. .531" I.D. x.937 O.D 2 710-0465 Hex Bolt 1/2-20x4.50" Lg.* x .09 3 711-0580 Clevis Pin 33 11459 Flail 4 711-0579 Flail Spacer 7/32" Lg. 34 711-0564 Flail Spacer 23/32" Lg. 5 11455-488 Cutting Finger 35 711-0578 Clevis Pin .50" Dia. x 3.0" Lg. 6 736-0921 L.-Wash. 1/2" Scr.* 36 736-0247 Fl.-Wash. .406" I.D. x 1.25" 7 726-0111 Palnut 3/16" Dia. O.D. Hdn. 8 712-0922 Hex Jam Nut 1/2-20 Thd.* 37 736-0217 L-Wash. 3/8" Scr. H.D. 9 714-0507 Cotter Pin 3/32" Dia. x 3/4" 38 710-0151 Hex Bolt 3/8-24 x 2.00" Lg. Lg.* H.T. 10 11465 -452 Chute Deflector 39 14575 -488 Flail Housing Ass'y- -Comp. N 11 712-0107 L-Nut 1/4-20 Thd. 40 712-0107 Hex Cent. L-Nut 1/4-20 Thd. 12 710-0289 Hex Bolt 1/4-20 x.50" Lg.* 41 11477 -452 Upper Guide Extension Ass'y. 13 714-0114 Sq. Key 1/4" x 2.00" Lg.* 42 11478 Hinge Pin 14 13430 -452 Impeller Assembly 43 726-0111 Palnut 3/16" Dia. 15 710-0157 Hex Bolt 5/16-24x3/4" Lg.* 44 712-0109 Wing Nut Elastic 1/4-20 Thd. 16 736-0119 L-Wash. 5/16" Scr.* 45 13431 -452 Blade 17 14573 -452 Hopper to Engine Mtg. Plate N 46 11460 -488 Guide Extension Assembly 18 Engine 47 11472 -488 Guide Extension 19 11464-488 Engine Mounting Plate 48 736-0264 FI-Wash. 5/16" Scr.* 20 712-0123 Hex Nut 5/16-24 Thd.* 49 11481 -488 Hopper Assembly 21 736-0119 L-Wash. 5/16" Scr.* 50 710-0601 Hex Wash. Hd. Self-Tap Scr. 22 738-0521 Shaft 5/16-18 x .50" Lg. 24 726-0221 Push Cap 51 11479 Clamp Rod Assembly 25 711-0494 Spacer 52 11454 -452 Back-up Plate 26 734-1056 Wheel Ass'y- - Comp. N 53 11467 -488 Inlet Guide Assembly 27 736-0100 FI-Wash. .50" I.D.* 54 09966 Knob Ass'y. 28 710-0624 Hex Bolt 5/16-24 x 1.50" Lg.* 55 11480 Stop Washer 29 712-0429 Elastic Stopnut 5/16-18 Thd. 56 711-0566 Chute Pivot Rod 30 710-0237 Hex Bolt 5/16-24 x....
Este manual também é adequado para os modelos :Jardim Shredders - 24650-A (1.82 mb)