Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Compare the illustrations with your shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper FIGURE 7.-Model 645 Shown OPERATING CONTROLS (See figure 7) RELEASE BAR—Used to release the leaf ranp when raising or lowering. CHOKE LEVER—Used to enrich the fuel mixture in the carburetor when starting a cold engine. STARTER HANDLE-Used to manually start the engine. THROTTLE CONTROL—Controls engine speed and stops the engine. The operation of any shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. F^SniiLAssEs)l Always wear safety glasses or eye r i^ A shields. We recommend wide vision safety mask for over spectacles or standard safety glasses. 6 BEFORE STARTING 1. Place the shredder on a firm, level surface. 2. Attach spark plug wire to spark plug. 3. Service engine with gasoline and oil as instructed in the separate engine manual packed with your shredder. 4. 8 H.P. Briggs & Stratton engine only: Open fuel shut-off valve. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to “Removing the Flail Screen" on page 9. TO START ENGINE A WARNING: Be sure no one other than the operator is standing near the shredder while starting or operating. 1. Place the throttle control lever in FAST position. See figure 8. 2. Move choke lever to CHOKE position (a warm engine may not require choking). 3. Grasp starter handle (see figure 8) and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. 4. Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. Do not let starter handle snap back against starter. 5. Repeat preceding instructions 3 and 4 until engine fires. When engine starts, move choke lever on engine halfway between CHOKE and RUN. 6. Move throttle control to IDLE position for a few minutes warm-up. Move choke lever to RUN position as engine warms up. NOTE: In order to idle smoothly, a new engine may require 3 to 5 minutes running above slow idle speed. Idle speed has been adjusted to be correct after this break-in period. TO STOP ENGINE 1. Move throttle control lever to STOP position. See figure 8. 2. Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. 3. 8 H.P. Briggs & Stratton engine only: Close fuel shut-off valve when unit is not in use to prevent fuel leakage. HOW TO USE YOUR SHREDDER Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e., branches, leaves, twigs, etc.). A WARNING: The shredder discharges material with considerable velocity. Keep away from the area around the chute deflector. Always stop the engine and disconnect the spark plug wire when removing or attaching the bag, when changing containers or when removing the shredded material, wear safety glasses and gloves whenever using your shredder. 1. Leaves and small branches up to 1/2" diameter can be fed into the hopper when it is in the raised position. See figure 9. If it becomes necessary to push material into the shredder, use a small diameter stick—NOT YOUR HANDS. The stick cannot exceed 1/2" in diameter so it will be ground up if it gets into the impeller assembly. A WARNING: Do not put material larger than 1/2" in diameter into the hopper. Material up to a maximum of 3" in diameter material may be fed into the chipper chute. Do not attempt to shred or chip any material larger than 3" in diameter. Personal injury or damage to the machine could result. FIGURE 9. 2. Leaves and small twigs can be raked into the shredder when the leaf ramp is lowered to the ground. See figure 10. Small branches up to 1/2" diameter can also be fed into the shredder in this position. See figure 11. ^ Throttle Control FIGURE 8.—Model 645 Shown 7 I iut.iiiltUu> mnnv.i.. I*»».»»•«. »•“■'«tvw,. FIGURE 10. No Larger Than 1/2" Diameter Ramp FIGURE 11. To lower the leaf ramp, use one hand tD grasp the handle at the top of the leaf ramp and lift slightly. Pull up on the release bar, and Icwer the leaf ramp to the ground. Release the tar. See figure 12. 3. Bulky material, such as stalks or heavy btanches, up to 3" in diameter should be fed nto the chipper chute. See figure 13. ▲ WARNING: Make certain leaf ramp is raised as shown when using the chipper chute. Also make certain the chipper chute door is closed when not in use. IMPORTANT: There is a flail screen located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in the Maintenance section on page 9. For best performance, it is important to keep th...
Este manual também é adequado para os modelos :Jardim Shredders - 645B (1.24 mb)