Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
It must be under WARNING! stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied the operator. SAVE THESE INSTRUCTIONS PRODUCT DESCRIPTION HOPPER (1) MOTOR SUPPORT (26) POWER SWITCH (47) CIRCUIT BREAKER (49) POWER CORD (58) CHUTE (32) STAND ASSEMBLY WHEEL/AXLE ASSEMBLY FIGURE D BODY (13) SKU 92281 For technical questions, please call 1-800-444-3353. PAGE 10 ASSEMBLY INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 17. WARNING! Always make sure the Power Switch (47) of the Chipper/Shredder is in its “OFF” position and the unit is unplugged from its electrical outlet prior to assembling the unit, unclogging the unit, or making any adjustments to the unit. The Body (13) is pre-attached to the Motor Support (26) by the manufacturer, and requires no additional assembly. (See Figure E.) To AttachThe HopperToThe Body: 1. If not already installed, insert all three Safety Nuts (8) into the slots in the Hopper (1) from the inside so that their round ends are inside the Hopper (1). (See Figure E.) 2. Place the Hopper (1) into the Body (13), lining up the Safety Nuts (8) with the slots in the Body. Secure the Hopper in place using Washers (9 & 10) and Screws (11). 3. Close the Body (13) and tighten the Knob (7) firmly to secure it in place. (See Figure E.) MOTOR SUPPORT (26) SAFETY SHUT-OFF SWITCH (42) FIGURE E HOPPER (1) BODY (13) KNOB (7) SAFETY NUT (8) HOPPER (1) To AssembleThe Stand: 1. NOTE: Assembling the Stand will require the use of the following hand tools provided as accessories; the 5mm Allen Wrench (69), 6mm Allen Wrench (70), 13mm Double End Wrench (71), and 16mm Double End Wrench (72). These wrenches should only be used when assembling the Chipper Shredder. REV 04/05 SKU 92281 For technical questions, please call 1-800-444-3353. PAGE 11 2. Attach the Left Support Leg (61) to the left side of the Motor Support (26), using two Screws (27), two Washers (34), and two Lock Nuts (33). (See Figure F.) 3. Attach the Right Support Leg (35)) to the right side of the Motor Support (26), using two Screws (27), two Washers (34), and two Lock Nuts (33). (See Figure F.) LEFT SIDE VIEW RIGHT SIDE VIEW RIGHT SUPPORT LEG (35) LEFT SUPPORT LEG (61) MOTOR SUPPORT (26) SCREW (27) WASHER (34) LOCK NUT (33) SCREW (27) WASHER (34) LOCK NUT (33) FIGURE F 4. Assemble the Wheel/Axle assemblies using the parts shown below. (See Figure (G.) WHEEL COVER (21) SCREW (22) WASHER (36) BUSHING (37) WHEEL (38) WASHER (36) SCREW (65) WASHER (36) AXLE (62) AXLE (62) END CAP (63) FIGURE G REV 06/06 SKU 92281 For technical questions, please call 1-800-444-3353. PAGE 12 OPERATING INSTRUCTIONS 1. WARNING! Use safety equipment. Always wear ANSI approved safety impact glasses under an ANSI approved full face shield, ANSI approved hearing and breathing protection, heavy duty work gloves, and nonskid safety shoes and work pants and work shirt. 2. Make sure to position the Chipper/Shredder on a flat, level, dry ground surface. Position the machine so that the Chute (32) is pointed in a safe direction, at least 25 feet from any people, animals, or objects. Then, chock both Wheels (38) of the machine with scrap branches or rocks to keep the unit from moving. 3. Connect an appropriate extension cord (not included) to the Power Cord Plug (58), and plug the extension cord into the nearest 115 volt, grounded, electrical outlet. (See Figure H, next page.) 4. Turn the Power Switch (47) to its “ON” position, and allow the Blades (15) to spin up to full speed. (See Figure H.) 5. Branches cannot be more than 1-1/4” in diameter. Do not attempt to force larger branches into the Chipper/Shredder. 6. Do not force the Chipper/Shredder. Let the natural suction process take in the material to be cut. Always stand clear and to the side of the Chute (32). (See Figure H.) 7. Without putting your hands into the Hopper (1), slowly drop the material in (one branch at a time). The machine will pull it in automatically. WARNING! Never use your hands to feed material into the Hopper (1). Always use the Feed Stick (59). (See Figure H.) 9. Should the Chipper/Shredder jam while in use, immediately turn the Power Switch (47) to its “OFF” position. Unplug the Power Cord (58). Loosen the Knob (7), and open the Body (13) to expose the Blades (15). Clear the jam. Close the Body, and retighten the Knob. Then plug the Power Cord into its extension cord, and turn the Power Switch to its “ON” position to resume cutting. (See Figures E and H.) 10. In extreme working conditions sensors in the Chipper/Shredder will automatically switch off the Motor to prevent overheating. In this event, turn the Power Switch (47) to its “OFF” position and unplug the machine from its electrical supply. Wait five minutes or until the Motor has cooled. Clear the machine of all debris. Depress the Circuit Breaker (49). Then, plug the machine into its electri...