Assessments - 6, GPA: 4
(
)
)
|
Facilidade de uso
Return machine for a replacement. • Avoid touching exposed blades on underside of confetti-cut shredder head. • Plug power cord in an outlet that can easily be reached. The plug is the primary electrical disconnect. • Make sure the electrical rating listed on the serial label (located near the power cord on the back of the shredder) matches the available electric power. • Do not place shredder near or over a heat or water source. • Secure shredder to wall with hardware provided in order to meet UL 60950 stability requirements. While operating shredder • Keep hands and hanging objects (jewelry, ties, loose clothing, long hair, etc.) away from paper entry. • Keep children and pets away from the shredder. When not in use • Always turn off and unplug shredder. • Unplug before emptying basket. • Do not open shredder head: Danger of electric shock. Opening shredder head will void the warranty. NOTE: Do not use flammable synthetic oil, petroleum-based products or aerosols of any kind on or near product at any time. ENGLISH 3 ENGLISHENGLISH Set-Up • Open the cabinet door and pull the waste basket (D) completely out of the cabinet. • Put plastic waste bag in basket (sample bags provided). Allow bag edges to overhang. Contact Fellowes to order more bags (part #36056). • Slide the waste basket into the cabinet and shut the cabinet door (A). • Plug the power cord into a convenient outlet. • Store this use and care manual in slot (M) inside cabinet door (A). Operation Control Switches H F G JI K Control Switch (H) Turbo Jam Release Button (F) Runs shredder when I AUTOMATIC button is held down. Turns on the automatic-start sensor and the green Ready light. O OFF Turns off the automatic-start sensor and the green Ready light. R REVERSE Runs shredder in reverse mode. Press and hold to activate. Troubleshooting Lights Ready Light (G) Paper Jam (I) Basket Full (J) Door Ajar (K) (Green) (Red) (Red) (Red) Shredder is in auto-Shredder is jammed Waste basket is full or Cabinet door is open. matic start mode. (e.g., too much paper paper has collected fed at one time). under cutting cylinders. For convenience and energy savings, your shredder is equipped with an automatic-start sensor (P). This means that when the control switch (H) is in the automatic [I] position, the shredder will start running when you put paper into it and stop a few seconds after the paper has passed through. CAUTION: The automatic-start sensor cannot tell the difference between paper and other objects. This feature can also be a hazard. Always turn off the shredder when it is not in use. Unplug the shredder if it will not be used for an extended period. To shred paper • Press the automatic [I] button. The green ready light (G) should turn on. • Feed paper straight into paper entry (B) releasing when the shredder begins shredding. To shred CDs or DVDs • Hold CD or DVD at the edge and feed one at a time, straight into CD entry (E), releasing when shredding begins. Shredder will stop when media has passed through entry. The media will be shred into small particles. CAUTION: Do not hold CD or DVD with finger through the center ring while feeding into shredder. 4 To empty waste basket If basket full light (J) is on, follow these steps until light turns off. • Press Turbo Jam Release Button (F) to finish shredding any paper in the paper entry. • Press the off [O] button. • Open the cabinet door (A) and pull out the waste basket (D). • Remove the full bag and replace with a new bag. • Slide the waste basket (D) into the cabinet and shut the cabinet door (A). To clear a paper jam If paper jam light (I) is on, follow these steps until light turns off. • Check the waste basket (D) and empty the bag if full. • Press and hold the reverse [R] button to back paper out of the paper entry (B). Try pulling gently on the paper to remove it from the shredder. • Alternate between forward and reverse, as needed, until the jam clears: – Press and hold the Turbo Jam Release Button (F) for a few seconds. – Press and hold the reverse [R] button for a few seconds. • Continue alternating between forward and reverse until the jam clears. CAUTION: The shredder may be damaged if you alternate too rapidly between forward and reverse. • Unplug shredder, open cabinet door (A) and remove wastebasket (D). • Carefully clear any paper shreds that have collected on under side of paper entry (B). CAUTION: Model 320C-2 (confetti cut model) has exposed blades on underside of paper entry. Use care when removing paper shreds. Maintenance Empty waste basket regularly to ensure the smooth functioning of the cutting cylinders. The shredder will not operate when the basket is full. Oil confetti-cut model (320C-2) regularly to ensure proper operation. If used at or near daily capacity, apply oil every time you empty the basket. Use Fellowes Powershred Lubricant #35250 or other non-aerosol vegetable-based oil in a long- nozzle container (sample oil provided). CAUTION: Do not use flammable synthetic oil, p...