Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Do not store next to corrosive materials, such as fertilizer. 8 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION Engine fails to start 1. Fuel tank empty, or stale fuel. 2. Spark plug wire disconnected. 3. Faulty spark plug. 1. Fill tank with dean, fresh fuel. 2. Connect wire to spark plug. 3. Clean, adjust gap or replace. Loss of power; operation erratic 1. Spark plug wire loose. 2. Unit running on CHOKE. 3. Blocked fuel line or stale fuel. 4. Water or dirt in fuel system. 5. Carburetor out of adjustment. 6. Dirty air cleaner. 1. Connect and tighten spark plug wire. 2. Move choke lever to OFF position. 3. Clean fuel line; fill tank with clean fresh gasoline. 4. Disconnect fuel line at carburetor to drain fuel tank. Refill with fresh fuel. 5. Adjust carburetor.f 6. Service air cleaner.f Engine overheats 1. Carburetor not adjusted properly. 2. Engine oil level low. 1. Adjust carburetor.f 2. Fill crankcase with proper oil. Too much vibration Loose parts or damaged impeller. Stop engine immediately and disconnect spark plug wire. Tighten all bolts and nuts. Make all necessary repairs. If vibration continues, have unit serviced by an authorized service dealer. Unit does not discharge 1. Discharge chute clogged. 2. Foreign object lodged in impeller. 1. Stop engine immediately and disconnect spark plug wire. Clean flail screen and inside of housing. See Maintenance section of this manual. 2. Stop engine immediately and disconnect spark plug wire. Remove lodged object. Rate of discharge slows considerably or composition of discharged material changes Shredding blade and/or chipper blades dull. Sharpen or replace shredding and chipper blades. fRefer to the engine manual packed with your unit. NOTE: For repairs beyond the minor adjustments listed above, please contact your nearest authorized service dealer. 9 242-640, 242A640 242-641, 242A641 NOTE This instruction manual covers various models, and all specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. 242-640, (242A6401 £u 242-641 .\242A6411 PARTS LIST FOR SHREDDERS REF. NO. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 742-0571 N Bladef 28 736-0242 Bell-Wash. .345" I.D. x .88" 13431 Bladeft 29 720-0170 Hand Knob 2 710-0818 Hex Patch Bolt 3/8-24 x 2" Lg. 30 747-0744A Chipper Door Rod (Gr. 8) 31 732-0542 Torsion Spring 1.14" Lg. 3 714-0114 Sq. Key 1/4 x 2.0" Lg. 32 781-0489 Chipper Door 4 736-0217 L-Wash. 3/8" I.D. H.D. 33 781-0475 Chipper Chute Ass’y. 5 736-0247 FI-Wash. .406" I.D. x 1.25" 34 736-0170 Spec. L-Wash. 5/16" I.D. O.D. Hdn. 35 712-3010 Hex Nut 5/16-18 Thd. (Gr. 5) 6 11459B Flail 36 781-0510 638 Shredder Frame 7 711-0564 Flail Spacer 37 710-0157 Hex Bolt 5/16-24 x .75" Lg. 8 711-0833A Clevis Pin .496" Dia. 38 736-0119 L-Wash. 5/16" I.D.* 9 711-0834 Flail Spacer w/. 160" Dia. Hole 39 710-3008 Hex Bolt 5/16-18 x .75" Lg. 10 715-0249 Spring Roll Pin 1.12" Lg. (Gr. 5) 11 736-0192 FI-Wash. .531" I.D. x .94" O.D. 40 710-0380 Hex Bolt 5/16-18 x 1.75" Lg.* 12 681-0002 N Impeller Ass’y. Comp.t 41 681-0004 N Flail Housing Ass’y.-L.H. 781-0484 Impeller Ass’y- Comp.ft 42 781-0474A Flail Housing Ass’y.-R.H. 13 781-0490 Chipper Blade 43 735-0639 Spark Plug Boot 14 710-1054 Flat Hd. Scr. 5/16-24 x .75" Lg. 44 - Engine 15 712-0411 Hex Top L-Nut 5/16-24 (Gr. 5) 47 712-0429 Elastic Lock Nut 5/16-18 Thd. 16 736-0119 L-Wash. 5/16" I.D.* 50 736-0264 FI-Wash. 5/16" I.D. 17 710-0825 Hex Bolt 1/4-20x3.75" Lg.* 52 781-0521 N Back-Up Plate 18 736-0142 FI-Wash. .281" I.D. x.50" O.D. 59 726-0214 Push Cap 5/8" Dia. Rod L 19 750-0793 Chute Hinge Spacer 1.66" Lg. 61 750-0786 Spacer .64" I.D. x .38" Lg. 90 711-0835 Clevis Pin .5" Dia. x 4.62" Lg. 62 738-0814 Shredder Axle >2 712-0291 Hex Ctr. L-Nut 1/4-20 Thd.* 63 734-1603 Wheel Ass’y. Comp. 23 714-3010 Cotter Pin 79 781-0519 N Hopper Support Brkt. 24 781-0457 Shredder Screen 80 781-0515 N Front Support Brkt. 25 714-0149B Internal Cotter Pin 3/8" Dia. 81 731-1307 N Leaf Hopper 26 781-0480 Chute Deflector Ass’y. — 764-0199A Bag (Not Shown) 27 712-3010 Hex Nut 5/16-18 Thd. (Gr. 5) — 723-0400 Safety Glasses (Not Shown) tModels 242A640 and 242A641 only. ttModels 242-640 and 242-641 only. *For faster service obtain standard nuts, bolts and washers locally. If these items cannot be obtained locally, order by part number and size as shown on parts list. CODE: N notates a new part (not previously existing). A three digit number is the color code. Specify color code as shown below if color or finish is important when ordering parts, [i.e., 638 for Red Finish]. NOTE: The engine is not under warranty by the shredder manufacturer. . .If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines-Gasoline.” Find It Fast In The Yell...
Este manual também é adequado para os modelos :Jardim Shredders - 242-640-000 (1.82 mb)
Jardim Shredders - 242A640-000 (1.82 mb)
Jardim Shredders - 242A641-000 (1.82 mb)